Melbourne switchboard with circuit breakers being checked
Electrical

Circuit breaker keeps tripping in Melbourne? Causes and safe next steps

Kevin · Licensed Electrician 8 min read

Circuit breaker keeps tripping: what to check

Infographic: Circuit breaker keeps tripping: what to check.

A breaker that trips once may be reacting to a one-off overload. A breaker that keeps tripping is a fault pattern. The safe response is to identify the likely load, reset once only, and stop if the fault returns.

First: do not keep resetting a tripped breaker

A breaker trips to interrupt an unsafe or excessive current. If it trips again after one safe reset, leave it off and arrange a licensed electrician. If you see smoke, sparks, scorch marks, water near electrical equipment, or smell burning, keep clear and do not touch the switchboard. Call emergency services if there is a fire.

In Victoria, electrical repairs and switchboard work are for licensed electricians. Do not remove a switchboard cover, touch exposed conductors or replace a breaker yourself. See Energy Safe Victoria's electrical safety guidance.

The three most common causes

1. Appliance fault

Kettles, toasters, heaters, dishwashers, washing machines, dryers and portable air conditioners are frequent offenders. If one appliance trips the breaker every time it starts, stop using it until it is tested or replaced.

2. Circuit overload

Overload happens when normal appliances draw more current than the circuit is designed to carry. This is common in older Melbourne homes where one power circuit now runs heaters, computers, kitchen appliances and chargers that were never part of the original load design.

3. Wiring or switchboard fault

If the breaker trips with little or nothing plugged in, the fault may be damaged cable, moisture, a loose connection, insulation breakdown, or a failing breaker. These require test equipment, not guesswork.

Is it a circuit breaker or a safety switch?

They protect against different conditions. A circuit breaker responds to overcurrent, such as an overload or short circuit. A safety switch (RCD) monitors for current leaking from the circuit and cuts power to reduce electric-shock risk. A combined RCBO can provide both types of protection. The exact device can be hard to identify from its appearance, so do not remove a switchboard cover or assume the cause from the label alone.

This distinction helps explain why a power point or appliance problem may trip a safety switch even when the household is not using too many appliances. If you are unsure which device tripped, tell the electrician what stopped working and what was running at the time.

Quick diagnostic table

PatternLikely causeNext step
Trips when one appliance startsAppliance fault or high start-up loadUnplug it and test the circuit without it
Trips when several appliances run togetherOverloaded circuitReduce load and ask about extra circuits
Trips after rainMoisture in outdoor outlet or lightStop resetting and book fault finding
Trips instantly with nothing plugged inWiring or board faultCall an electrician urgently

When it becomes urgent

Call immediately if there is a burning smell, buzzing, heat at the board, scorch marks, sparks, smoke, water exposure, or if the same circuit trips twice after one safe reset. If there is fire or smoke, call 000 first.

What an electrician tests

A licensed electrician can isolate the circuit, test insulation resistance, confirm polarity and earth continuity, inspect the switchboard, and test the breaker under load. The result should be a clear answer: appliance fault, circuit overload, damaged accessory, cable fault or board issue.

For an overload, the electrician can check the circuit rating, connected loads and how appliances are distributed around the home. The solution may be a change in how loads are used, a new dedicated circuit, or another repair. If the cause is intermittent, note whether it follows rain, a particular appliance starting, or a certain time of day. Those details can help narrow the fault without putting you at risk.

FAQ

Can I replace a circuit breaker myself?
No. Switchboard work is licensed electrical work in Victoria.
Is one trip dangerous?
Not always. A repeat trip, heat, smell, buzzing or sparks is a stronger warning sign.
How much does breaker fault finding cost?
Simple fault finding may be a standard call-out. Repairs vary depending on whether the problem is an accessory, appliance, cable or switchboard component.

For local help, see our Melbourne electrical services, electrician in Richmond, or electrician in Melbourne CBD. Related guides: buzzing powerpoint in Melbourne, what to do when a circuit breaker trips twice, a power point tripping a safety switch, and ceiling fan installation cost Melbourne 2026.

Need a Melbourne electrical technician?

We're one call away — 24/7 emergency service, live answer, upfront pricing.