Evaporative Cooler Not Cooling, Leaking or Smelling? Common Melbourne Fa
Heating & Cooling

Evaporative Cooler Not Cooling, Leaking or Smelling? Common Melbourne Faults

24/7 Service Mate · Heating and cooling advice team 8 min read

Evaporative Cooler Not Cooling, Leaking or Smelling?

Infographic: Evaporative Cooler Not Cooling, Leaking or Smelling?
Evaporative coolers are popular in Melbourne\

Evaporative coolers are popular in Melbourne's northern and western suburbs — they're cheap to run and effective in the hot, dry conditions Melbourne's inland areas experience. But they have a distinct set of problems that refrigerative air conditioners don't. Here's how to diagnose the most common faults.

How evaporative cooling works — and why it matters for faults

An evaporative cooler (also called a swamp cooler) draws hot outside air through water-saturated pads. As air passes through the wet pads, evaporation cools it by 8–14°C, and the cooled air is pushed through ducts into the home. Unlike refrigerative systems, evaporative coolers add humidity to air and require windows or doors to be left ajar for the system to work.

Key implication: If it's humid outside (Melbourne's autumn and spring changeable days), evaporative cooling doesn't work as well — this is a property of the technology, not a fault.

Problem 1: Not cooling effectively

Common causes

  • Pads are dry, clogged, or mineral-scaled: Pads must be thoroughly wet to cool air. Scale from Melbourne's moderately hard water blocks water distribution over time
  • Water pump failure: No water reaching pads = no evaporation = warm air output
  • Outside humidity above ~50%: In humid conditions, evaporation is significantly reduced — not a fault, just physics
  • Fan speed too low: Higher fan speeds increase cooling in dry conditions
  • Windows and doors not open: Evaporative cooling requires exhaust air pathways

DIY checks

Inspect pads (usually quarterly) — they should be evenly damp and free of white mineral scale. Flush the tank to remove sediment. Test the pump by verifying water flow across all pads during operation.

Problem 2: Water leaking from the unit or ceiling

Causes and fixes

SymptomLikely causeFix
Water dripping inside from ceiling ventsFloat valve set too high — tank overfillingAdjust float valve to lower water level
Water pooling under rooftop unitCracked or corroded base trayTray replacement; sealant for minor cracks
Water stains on ceiling around grilleDistribution hose split or blocked; water overflowing padsReplace distribution hose or redistributor
Water running down walls near unitBlocked overflow drainClear drain; ensure unit is level

Problem 3: Musty or mouldy smell

The combination of moisture, warmth, and organic material (dust, pollen, bird debris) in evaporative coolers creates ideal conditions for mould and bacteria growth. This is one of the most common evaporative cooler complaints in Melbourne homes.

Sources of smell:

  • Stagnant water in the tank at end of season (always drain before switching off for winter)
  • Mould on pads — pads that aren't dried properly harbour mould between uses
  • Bird nesting on or in the unit — common with rooftop evaporative coolers
  • Algae growth in the water reservoir

Fix: Full unit clean, pad replacement, tank flush, and application of biocide treatment. Annual end-of-season maintenance prevents most odour problems.

Problem 4: Unit won't turn on or no airflow

  • Check the circuit breaker at the switchboard
  • Check the wall controller has power and is set to cooling/fan mode
  • Inspect the start capacitor (professional repair) — the most common cause of fan motor not starting
  • Check for seized bearings in the fan motor (usually produces a humming noise when power is applied)

Annual maintenance checklist

TaskWhen
Pad inspection and replacement (if scaled)Start of each season
Tank flush and cleanStart and end of season
Water distribution checkStart of season
Float valve adjustmentStart of season
Motor and belt inspectionAnnual service
Drain tank and run dryBefore winter shutdown

Evaporative cooling and Melbourne’s weather: limitations you should know

Why evaporative cooling struggles on Melbourne’s humid summer days

Evaporative cooling works by passing hot dry air over wet pads, causing water evaporation that cools the air. This process only works effectively when the outside air is dry (low relative humidity). Melbourne’s summer humidity ranges widely — on a classic dry northerly day (35°C, 15–25% humidity) an evaporative cooler is highly effective and can cool a home by 10–15°C. On a muggy southerly change day (28°C, 65%+ humidity), an evaporative cooler adds moisture to already-humid air and provides minimal temperature reduction.

This is not a fault — it is the fundamental thermodynamic limit of evaporative cooling. Homeowners in Melbourne who rely solely on evaporative cooling often add a portable or split system unit for the approximately 15–20 days per summer when humidity is too high for effective evaporative operation.

Legionella risk and water quality

The standing water in evaporative cooler tanks and pads is a potential Legionella growth environment. Victorian health authorities (DHHS) recommend:

  • Full clean and pad replacement before each cooling season
  • Running the unit on fan-only for 30 minutes before first use to flush the system
  • Draining the tank if the unit will not be used for more than 2 weeks
  • Annual professional service including pad inspection and water treatment

An annual evaporative cooler service by 24/7 Service Mate includes pad inspection and replacement (if worn), water distribution tray cleaning, pump check, and motor belt inspection. Cost is typically $180–$280 depending on unit size and roof access.

Duct leaks and roof space heat in Melbourne summers

In Melbourne’s January and February, roof space temperatures can exceed 55°C during peak afternoon heat. Evaporative cooler ductwork running through an uninsulated roof space gains heat rapidly, reducing cooling performance. If your evaporative system felt effective 5 years ago but now seems weaker, duct leaks or missing duct insulation are likely causes. A duct inspection (included in our service) can identify and seal leaks.

Evaporative cooler replacement vs repair: Melbourne cost comparison

Repair is usually the right choice if the unit is under 12 years old and the fault is a single component (motor, pump, pad frame). Common Melbourne evaporative cooler repair costs: pad replacement $180–$340 depending on unit size; pump replacement $150–$220; motor replacement $280–$420. If the unit is older than 15 years with multiple worn components, replacement is often better value. A new evaporative cooler supply and installation in Melbourne typically costs $1,800–$3,500 depending on unit capacity and roof access. The Victorian Energy Upgrades (VEU) program does not currently list evaporative coolers as an eligible activity, but upgrading to a reverse-cycle split system may attract a VEU incentive. 24/7 Service Mate’s Andy can assess your current unit and provide honest repair vs replace advice. Call 1300 24 11 47.

When booking an evaporative cooler service or repair in Melbourne, look for a technician who is a licensed plumber (required for any water connection work) and experienced with your brand and model. 24/7 Service Mate’s Andy and the HVAC team service all major evaporative cooler brands across Melbourne including Breezair, Bonaire, and Coolair.

Regular servicing ensures your evaporative cooler runs efficiently and safely throughout the Melbourne summer cooling season.

FAQ

When should I replace evaporative cooler pads?
Cellulose pads typically last 2–5 seasons depending on Melbourne's water hardness and usage. Replace when mineral scale is visible and doesn't wash off, or when pads are crumbling. Synthetic pads (Chillcel) last longer but are less efficient.
Is evaporative cooling suitable for Melbourne's climate?
Yes, in Melbourne's hotter inland and outer northern/western suburbs (Sunbury, Melton, Werribee, Craigieburn). Coastal suburbs (Port Melbourne, St Kilda, Brighton) with higher humidity get less benefit. For year-round comfort in Melbourne, refrigerative reverse-cycle provides better coverage across the climate variability.

Evaporative cooler service in Melbourne

Full-service evaporative cooler maintenance, pad replacement, and repairs. Call 1300 24 11 47.

For local help, see our Melbourne HVAC services, HVAC technician in Richmond, HVAC technician in St Kilda. Our emergency HVAC repair in Richmond page covers scope, pricing and 24/7 dispatch. Emergency? See our emergency HVAC repair in Richmond. Related guides: Air Conditioner Service Cost Melbourne 2026, Ceiling fan installation cost Melbourne 2026.

Need a Melbourne heating & cooling technician?

We're one call away — 24/7 emergency service, live answer, upfront pricing.