Zones are dampers in the duct, not magic. Close too many and the system either roars at one outlet or ices the indoor coil. A dump zone or a minimum-open setting is how a good design survives a Melbourne family that only wants the living room cold.
The short version
- Zones are dampers in the duct, not magic. They redirect air, they do not create capacity.
- Close too many and the system either roars at one outlet or ices the indoor coil.
- A dump zone or a minimum-open setting is how a good design survives a family that only wants the living room cold.
- Good zoning starts with a load calculation and a duct layout, not a brochure.
- Most zoning complaints are airflow and design issues, not faulty refrigerant.
Design, not gadgets
A zoned ducted system is a single indoor unit and outdoor unit connected to branches of ductwork, each branch fitted with a motorised damper. A controller opens and closes dampers based on a schedule, thermostats or sensors. The compressor and fan work to meet the total demand of whichever zones are open. If only one small bedroom is open on a system sized for the whole house, the fan has nowhere to push air, pressure rises, noise increases, and the coil may freeze.
A well-designed system includes a bypass or a dump zone, a minimum airflow setting, and ducts sized for each zone. Typical zones in a Melbourne family home: living and kitchen, master bedroom suite, secondary bedrooms, and a study or rumpus. Two-storey homes often separate upstairs from downstairs, which suits the way heat rises in summer and winter. Related: ducted air conditioning cost 2026 and ducted heating types in Australia.
How many zones do you need?
- Two zones (day and night): simple and cost-effective for a typical three-bedroom home.
- Three or four zones: suits a larger home with a separate parents’ retreat or a home office.
- One zone per room: only in very large homes, since more zones need more ducts, dampers and controls, and each one adds cost and complexity.
The cheapest comfort per dollar usually comes from fewer, well-chosen zones with enough airflow to each, rather than many tiny zones.
Common Melbourne faults
- One room never reaches temperature: undersized duct, a kinked flexible duct in the roof, a closed balancing damper or a zone motor that has stopped moving.
- Loud rush of air when only one zone is open: no bypass or minimum-open setting, so the fan is forcing too much air through a small outlet.
- Zone controller shows the wrong temperature: a sensor placed in sunlight, a battery issue or a miswired cable.
- Frosted indoor coil with several zones shut: airflow too low for the coil, often combined with a blocked return filter.
- Zones open and close at odd times: a schedule left over from last winter, or a controller reset after a power cut.
In many older homes, the ducts sit in a hot roof space. In summer, a poorly insulated duct can lose a lot of cooling before air reaches the room, which looks like a zone fault but is really a duct insulation issue. See ducted aircon not cooling and uneven ducted zones.
Running habits that help
- Do not shut every zone but one for long periods. Keep at least the minimum airflow that the installer set.
- Use schedules: living zones on during the day, bedrooms before bed, and off when empty.
- Set realistic temperatures: 23–25°C in summer and 19–21°C in winter, avoiding large swings.
- Wash or replace the return filter regularly. A clogged return affects every zone.
- Close curtains on sunny sides and keep doors open between zones that share a similar load.
Cost guide for 2026
Guides only; we quote after a site visit and a load calculation.
- Servicing and zone check on an existing system: typically a few hundred dollars.
- Replacing a zone motor or damper: commonly a few hundred dollars plus roof access.
- New or upgraded zone controller: often several hundred dollars, more with wireless sensors.
- Adding a zone to an existing system: depends on duct work and may need a new damper and cable run.
- Full supply and installation of a new zoned ducted system: usually in the high thousands to low tens of thousands, depending on size and zone count.
What a licensed technician checks on a zoning fault call
- Controller programming, schedules and any lock or override settings.
- Each damper motor, tested by commanding it open and closed and watching its movement from the roof or at the plenum.
- Supply and return temperatures at the indoor unit, which show whether the refrigeration side is behaving.
- Static pressure in the ductwork, which shows whether airflow is restricted or the fan is struggling.
- Outlet airflow in each room, using a flow hood or a simple measurement against the design.
- Duct condition: kinks, crushed sections, disconnected joints and missing insulation.
Static pressure matters more than most owners realise. A system designed for a certain pressure can run noisy and inefficient if the filter is clogged, the return grille is too small or a bedroom door is shut with no return path. For bedrooms, a transfer grille or a gap under the door lets air return so the zone works as designed.
Retrofitting zones to an older system
Many older ducted systems in suburbs like Malvern and Hawthorn have no zoning at all: one thermostat, one setting, all outlets open. Retrofitting dampers and a controller is possible, but only if the duct layout allows branches to be isolated and the fan can handle reduced airflow. We often recommend adding a bypass damper and a variable speed fan, or replacing the indoor unit at the same time. Related: ducted heating service cost and split system vs ducted.
FAQ
- Can I run one bedroom all night?
- On a well-designed system with a bypass or minimum-open zone, yes. On a poorly designed one, it can be noisy and icy. We check the settings for you.
- Do I need a zone per room?
- Rarely. Grouping rooms with similar use and orientation works better and costs less.
- Wi-Fi control worth it?
- It is handy for schedules and remote switching. It does not fix a design or airflow problem.
- Gas ducted plus refrigerated add-on?
- Possible, with a shared duct system and a dedicated cooling coil, but the airflow and duct sizing must suit both modes. See hydronic vs ducted reverse cycle.
- Two-storey?
- Often best with two zones or two systems, one per level, because heat rises and loads differ.
- Does zoning save energy?
- Yes, if you use it. Cooling only the rooms you occupy costs less than the whole house.
Related reading
See HVAC, ducted air conditioning, heating and cooling system replacement, HVAC in Narre Warren and HVAC in Brunswick.
Zones not behaving?
We check dampers, airflow and settings before suggesting parts. Call 1300 24 11 47.