Home security camera installation with outdoor weatherproof power in Melbourne
Electrical Safety

Home security system installation Melbourne: cameras, sensors, outdoor power, and what a licensed electrician actually does

Kevin · Licensed Electrician 8 min read

Home security system installation Melbourne: what to check

Infographic: Home security system installation Melbourne: what to check.

Installing a home security system in Melbourne involves two distinct scopes: the security company handles the devices, monitoring and app setup; a licensed electrician handles the electrical infrastructure — permanent power points, weatherproof outdoor outlets, PoE data cabling routes, security lighting circuits and any switchboard modifications. Getting both trades working together from the start makes the install faster, cleaner and fully compliant with AS/NZS 3000 wiring rules.

Need power or cabling for your security system?

Our licensed electricians work alongside your security installer — call 1300 24 11 47 to coordinate.

The short version

  • Security cameras and sensors can be wired (PoE), wireless (Wi-Fi/battery) or a mix. Each has different electrical infrastructure needs.
  • A licensed electrician must install permanent power points, outdoor weatherproof GPOs, new lighting circuits and any switchboard modifications.
  • Security companies can run low-voltage data cable and connect devices — they do not hold an electrical licence and cannot modify mains wiring.
  • Planning the electrical scope before installation day avoids costly revisits for cameras that have no power or cabling routes.
  • Security lighting — motion-activated or always-on — is among the most effective security measures and is an electrician-only task.

Wired vs wireless security systems: the electrical implications

The most common decision when planning a security system is whether to go wired, wireless, or hybrid. From an electrical perspective, the key question is not which looks better on camera — it is what infrastructure the home needs to support the chosen system reliably.

System type Electrician scope Security company scope Typical electrician cost add
Wireless (Wi-Fi cameras, battery or plug-in) Weatherproof outdoor GPOs near camera positions; Wi-Fi range check; ensure existing circuits can handle extra loads Mount and configure cameras, connect to app and monitoring $300–$600 for 2–4 outdoor GPOs
PoE wired (IP cameras over Cat 6) Data cabling routes through walls/ceiling; cannot run cables that breach fire compartments without approved products Terminate Cat 6, connect PoE switch/NVR, configure cameras Security company typically runs cable; electrician needed if routes involve mains cable proximity issues or switchboard for NVR power
Hybrid (some wired, some wireless) Mixed scope — plan each camera position Mixed scope $400–$900 depending on outdoor GPO count and cabling runs
Hard-wired traditional alarm system Dedicated circuit for alarm panel; siren mounting power; tamper-evident conduit routes in some configurations All sensor, detector and panel installation under their own licence $200–$500 for dedicated circuit and panel power

What an electrician does during a security system installation

Outdoor weatherproof power points

Most security cameras — even PoE systems — need a power point somewhere nearby for the NVR or router, or as a backup power source for Wi-Fi cameras. Outdoor GPOs must be weatherproof to at least IP44, installed in a weatherproof enclosure, and protected by a safety switch (RCD). A licensed electrician is required for all outdoor mains wiring under Victoria’s Electricity Safety Act. This is not a DIY task — outdoor cable runs must be correctly protected against physical damage and moisture ingress.

Security lighting circuits

Motion-activated security lighting is consistently rated by Victorian police and the Victorian Government’s crime prevention guidelines as one of the most effective deterrents for opportunistic property crime. Installing security lights — particularly on side gates, driveways, carports, backyards and entry points — is fully within the electrical scope and is a common add-on when a security system is being installed.

Options range from basic sensor floodlights on existing circuits to dedicated security lighting circuits with their own breaker. For complex multi-zone lighting, a dedicated circuit gives the cleanest installation and allows the lights to function independently of other loads.

Data cabling routes (in wall or ceiling)

For PoE (Power over Ethernet) camera systems, Cat 6 data cable runs from each camera position to the NVR or PoE switch. Data cabling is technically low-voltage and does not require an electrical licence for the cable run itself — but it does require an electrician in several scenarios:

  • When cables must pass through the same wall or conduit as mains wiring, Australian wiring rules require physical separation.
  • When cables pass through fire-rated walls or floors, only approved cable types and penetration sealing methods can be used.
  • When cables are run externally and require weatherproof conduit — conduit attached to the house exterior may still require council consideration depending on heritage overlays in some Melbourne suburbs.

Switchboard work for NVR or alarm panel power

A Network Video Recorder (NVR) is a critical piece of equipment that should be on a reliable, surge-protected circuit. If your system includes a professional-grade NVR with UPS (uninterruptible power supply), an electrician may be asked to install a dedicated circuit from the switchboard to keep the recorder on a clean supply separate from high-load appliances.

Professional alarm panels also typically need a dedicated circuit or at least a protected outlet from a quality surge board. The electrician ensures this is on the right circuit type and that the switchboard has capacity to add it cleanly.

When to call the electrician first

⚠️ Get the electrical scope sorted before installation day

If the security installer arrives and there is no outdoor power point, no pre-run cable route, and the NVR needs a new circuit, the job stops. A quick pre-installation consult with an electrician — even a 20-minute site visit — avoids this scenario and means both trades can work in sequence rather than chasing each other.

The best sequence for a new security system installation in Melbourne is:

  1. Choose your system and camera positions — mark them on a rough floor plan.
  2. Book an electrician to assess outdoor GPO positions, lighting requirements and any cable route constraints.
  3. Electrician installs outdoor power points, new circuits and any conduit or cable route preparation.
  4. Security company installs cameras, sensors, NVR/DVR and completes app and monitoring setup.
  5. Electrician returns (if needed) to tidy conduit, connect NVR power and complete the Certificate of Electrical Safety.

How much does the electrical scope cost in Melbourne?

The electrical cost for a home security installation depends primarily on the number of outdoor GPOs, whether security lighting is included, and whether any switchboard work is needed.

Scope item Typical Melbourne cost Notes
Outdoor weatherproof GPO (each) $180–$280 Includes RCD protection; higher at end of long cable run
Security floodlight (sensor, mounted) $220–$380 Per light; includes wiring to existing circuit where available
Dedicated security lighting circuit $350–$600 New breaker from switchboard; suited to multi-zone systems
NVR/alarm panel dedicated circuit $250–$450 Clean supply from switchboard for recorder or panel
Switchboard assessment and minor upgrade $400–$900 Only if additional circuits exceed current switchboard capacity

For a standard 3–4 bedroom Melbourne home with 4 cameras (2–3 outdoor GPOs) and 3–4 security lights, the electrical scope typically runs $900–$1,800 as a standalone job. Costs are lower when combined with other electrical work on the same visit.

For full licensing requirements, Energy Safe Victoria’s electrician licensing information sets out who can legally carry out mains electrical work in Victoria.

How 24/7 Service Mate handles security installation electrical work

Our Melbourne electricians regularly work alongside security installers. When you book us for the electrical scope, we confirm the camera positions, agree on the cleanest outdoor GPO locations, plan the conduit and cable routes through the roof or walls, and have the Certificate of Electrical Safety ready at job completion.

We can carry out the electrical scope as a standalone pre-installation visit or at the same time as the security company if both trades can be on site together. Our teams cover inner Melbourne including Richmond, Fitzroy and surrounding suburbs. Call 1300 24 11 47 to discuss your system and get a quote for the electrical side.

FAQ

Do I need a licensed electrician to install outdoor security cameras?
Not for the camera or cable itself — but you do need a licensed electrician to install the outdoor power point that the camera or its power adapter plugs into, and to install any security lighting on mains circuits. Outdoor mains wiring of any kind in Victoria is licensed electrical work.
Can a security company run cable through walls?
A security installer can run low-voltage data cable (Cat 6, coax) for cameras and sensors without an electrical licence, provided the cable does not share conduit or wall space with mains wiring without proper separation. If the routes require mains proximity work or fire-rated penetrations, an electrician should be involved.
What is the difference between a PoE camera system and a traditional CCTV system?
PoE (Power over Ethernet) cameras receive both data signal and power through a single Cat 6 cable connected to a PoE switch or NVR. Traditional analogue CCTV uses coaxial cable for video and requires separate power at each camera. PoE systems are cleaner to install and are now the most common choice for new residential installations in Melbourne.
Should the NVR be on a dedicated circuit?
For professional-grade systems where continuous recording is important, a dedicated circuit for the NVR is good practice. It ensures the recorder is not competing with high-load appliances on the same circuit and makes it easier to pair with a UPS. For basic home systems, a quality surge-protected outlet on an existing circuit is often sufficient.
What security lighting gives the best deterrence?
Motion-activated LED floodlights on driveway, side gate, and rear access points are the most effective. Always-on lighting at entry points (front door, garage) adds to safety without the movement distraction. Visible cameras combined with lighting are consistently more deterrent than cameras alone.

For more on our electrical services, visit the Melbourne electrical services hub. Outdoor power installation details are on our outdoor power points page. For switchboard capacity planning before adding circuits, see our switchboard upgrade cost guide and our switchboard and safety switch upgrades service. If you are also considering surge protection for your NVR or electronics, read our whole-home surge protection guide.

Need a Melbourne electrical safety technician?

We're one call away — 24/7 emergency service, live answer, upfront pricing.