Electrician testing a power point in a Melbourne home
Electrical

Power points not working? Room-by-room diagnosis before you call

Kevin · Licensed Electrician 5 min read

Power points not working? Room-by-room diagnosis before you call

Infographic diagram for Power points not working? Room-by-room diagnosis before you call.

A dead outlet can be a tripped circuit, failed appliance, loose connection or damaged power point. Here is the safe way to narrow it down without touching wiring.

Need a dead power point diagnosed?

Call 1300 24 11 47 for Melbourne fault finding. Stop using any hot, loose or damaged outlet.

The short version

  • Identify whether one outlet, one room or the whole property is affected before booking.
  • Try a known-working low-load device, then inspect the closed switchboard for a tripped device.
  • Unplug everything before one reset attempt; do not keep resetting a circuit that trips.
  • Heat, burning smell, buzzing, sparks, water and cracked plastic make the fault urgent.
  • A licensed electrician should repair any fixed outlet or wiring fault and provide a CoES where applicable.

Start with the pattern

Is one outlet dead, one room affected, or all power points in the house out? The pattern tells you whether to look at the appliance, the outlet, the circuit or the switchboard.

Safe checks you can do

  • Unplug the appliance and try a known working low-load item, such as a phone charger.
  • Check whether nearby outlets are also out.
  • Look at the switchboard without removing covers.
  • Check whether the fault followed rain, cleaning, renovation or a high-load appliance.

Stop immediately for these signs

Do not keep testing an outlet that is cracked, loose, hot, buzzing, sparking, discoloured, wet or smells burnt. These signs can point to arcing or a loose termination behind the plate.

What the pattern usually means

PatternLikely issueCall priority
One outlet deadFailed outlet or loose connectionScheduled unless hot/sparking
One room deadTripped circuit or cable faultSame day if repeated
Outdoor point dead after rainMoisture ingressUrgent if wet or tripping
All power outMain switch, outage or major board faultUrgent

Why old Melbourne homes are different

Older terraces, apartments and post-war homes often have fewer power circuits than modern usage requires. A room full of powerboards may be a symptom of too few outlets and too much load on one circuit.

Authority note

Fixed wiring and power point repairs must be done by licensed electricians. See Energy Safe Victoria for Victorian electrical safety and licensing information.

Room-by-room triage you can do safely

Reset the RCD covering that room. Unplug everything on the dead circuit. If the RCD holds, plug back one item at a time. If it trips empty, call a licensed electrician — the fault is likely in the wiring.

What the pattern tells an electrician

One dead outlet can be an isolated failed accessory, loose termination or damaged connection. Several dead outlets in a row often indicate a fault at an upstream point because outlet circuits are commonly looped. If every outlet is out but lights remain on, it may be a single power circuit or safety switch. A whole-house outage calls for a check of the main switch, supply status and switchboard. The symptoms guide efficient testing, but no pattern can safely replace electrical measurements.

Safe checks before you book

Use a phone charger or another known-working, low-load item to confirm that the appliance is not the issue. Check nearby outlets and note whether the problem began after rain, cleaning, renovation, a heater or a kitchen appliance. With the switchboard cover closed, see whether a breaker or safety switch is visibly tripped. After unplugging loads, reset once only. If it holds, reconnect appliances one at a time. If it trips with nothing connected, stop and arrange fault finding.

Why intermittent outlets are not harmless

An outlet that works only when a plug is moved, feels warm, crackles or shows brown marks may have a loose connection behind the plate. Resistance at a poor connection creates heat, particularly with high-load appliances, and can damage the accessory or cable. Do not tighten screws, change the outlet or push a loose plug into place. Keep the circuit unloaded and have it checked. For immediate smoke, fire or electric shock risk, call 000.

How the repair is scoped

We test the circuit protection, confirm supply at accessible points and trace the fault methodically. The fix may be a failed outlet, a damaged cable, moisture in an outdoor fitting, a faulty appliance or an overloaded circuit. If a room consistently relies on boards and extension leads, we can also quote additional outlets or a dedicated circuit. New or altered electrical work in Victoria is completed by a licensed electrician and a Certificate of Electrical Safety is supplied where required.

FAQ

Can I replace a power point faceplate myself?
No. A fixed outlet is electrical installation work, not a cosmetic DIY task.
Why did my outdoor outlet stop after rain?
Moisture may have caused protection to operate. Leave it isolated if it trips and have the weatherproof fitting checked.
Can one appliance cause outlets to fail?
Yes. An appliance fault can trip the circuit; unplug all loads before one reset attempt.
Should I use an extension lead from another room?
Only temporarily for low-load equipment and never as a permanent replacement for a faulty circuit.
When is a dead outlet urgent?
Urgent signs include heat, smell, arcing, water, discolouration, shock or repeated tripping.

Fix the cause, not the inconvenience

A dead outlet is often straightforward, but the safest repair depends on knowing whether the issue is the appliance, accessory, circuit or switchboard. Proper diagnosis prevents a temporary workaround from hiding a more serious fault.

FAQ

Can I replace the outlet plate myself?
No. Replacing a fixed power point is electrical work.
Why do lights work but outlets do not?
Lighting and power are usually separate circuits.
Should I keep using an outlet that sometimes works?
No. Intermittent outlets can indicate a loose connection.

For local help, see our Melbourne electrical services, electrician in Richmond, electrician in Melbourne CBD. Our power point installation page covers scope, pricing and 24/7 dispatch. Emergency? See our emergency electrician in Richmond. Related guides: Overloaded power points: how many appliances is too many?, Ceiling fan installation cost Melbourne 2026.

Need a Melbourne electrical technician?

We're one call away — 24/7 emergency service, live answer, upfront pricing.