Power point installation in Melbourne typically costs $150–$300 to replace an existing outlet on a live circuit, $300–$550 to add a new point on an existing circuit, and $450–$650 or more when a new cable run, wall chasing or switchboard work is required. The biggest price variables are access, board condition and whether the job is a like-for-like swap or a new circuit addition.
Need a power point installed or replaced?
Call 1300 24 11 47 — we quote the exact scope on site before work starts.
The short version
- Replace existing power point (like for like): $150–$300 per outlet in Melbourne.
- New power point on existing circuit: $300–$550 per outlet.
- New power point with cable run through walls or ceiling: $450–$650+.
- USB or smart outlet upgrade: add $40–$120 per point for the fitting.
- Outdoor weatherproof power point: $350–$650 depending on cable routing and IP rating.
Why power point prices vary across Melbourne homes
Two neighbours in Preston might both want "one new power point behind the TV" and receive quotes $200 apart. That gap usually reflects real differences in how the cable gets there, not one electrician overcharging.
Replacement vs new installation
Swapping a cracked or yellowed GPO where the wiring behind it is sound is a 20–40 minute job. Adding a new outlet means running cable from the nearest point on the circuit — through a timber stud wall in a 1990s Craigieburn build, or through double brick and plaster in a 1920s Brunswick bungalow. Brick and solid-wall homes in inner Melbourne routinely cost more for new points than lightweight timber-frame outer-suburb homes.
Wall and ceiling access
Surface-mounted conduit on a garage wall is faster than chasing into rendered brick. Ceiling-mounted points for pendant lights or above kitchen benches may require roof-space crawling — slow work in low-pitch terraced roofs common in Richmond and Collingwood. If the electrician cannot fish cable through existing cavities, the price rises with every hour of access work.
Switchboard and circuit capacity
Adding multiple outlets or high-draw appliances — induction cooktops, heat pump dryers, home office setups — may require a dedicated circuit or an RCD-protected sub-circuit. If the board has no spare ways or no RCD on the target circuit, the power point job triggers switchboard work. See our switchboard upgrade cost guide for those ranges.
Compliance and certification
New circuits and alterations in Victoria require a Certificate of Electrical Safety. Your licensed Melbourne electrician must test, certify and lodge the work with Energy Safe Victoria where applicable. Certification should be included or clearly itemised — not omitted from the quote. Details at Energy Safe Victoria.
Common Melbourne power point job costs 2026
| Job | Typical Melbourne range | Main cost variable |
|---|---|---|
| Single GPO replacement | $150–$300 | Back-box condition, access |
| Double GPO replacement | $180–$350 | Whether rewiring needed at terminals |
| New GPO on existing circuit (same wall) | $300–$450 | Cable fishing difficulty |
| New GPO with cross-room cable run | $450–$650 | Wall type, ceiling vs wall route |
| USB combo outlet installed | $220–$420 | USB fitting cost, circuit load check |
| Outdoor weatherproof GPO | $350–$650 | IP rating, cable route, RCD protection |
| Multiple GPOs (3–4, same room) | $700–$1,400 | Quantity discount, shared cable runs |
| Kitchen bench power upgrade (dedicated circuit) | $600–$1,200 | Appliance load, board capacity |
Ranges cover labour and standard fittings. Premium designer plates, smart outlets, switchboard remediation and after-hours attendance are additional unless stated in the quote.
Power point types and when each makes sense
Standard double GPO
The default for most Melbourne rooms. A quality fitting with shuttered sockets costs $15–$35 in materials. Suitable for bedrooms, living areas and general use.
USB combo outlets
Popular in kitchens, bedside tables and home offices. The fitting costs more ($40–$90) and the electrician should confirm the circuit is not already near capacity from other fixed loads. Read our USB power point installation guide for upgrade considerations.
Weatherproof outdoor GPO
Required for external use — BBQ areas, garden sheds, pool equipment. Must be on an RCD-protected circuit with appropriate IP rating. Outdoor installs in coastal suburbs like Brighton and Williamstown may need higher corrosion resistance. See outdoor power point installation Melbourne.
20-amp outlets
Needed for some commercial-grade appliances and workshop equipment. Requires heavier cable and a dedicated breaker — not a simple swap from a standard 10-amp point.
What a fair power point quote should include
- Whether the job is a replacement or a new cable run — and the proposed route.
- Fitting type and brand (standard, USB, weatherproof, smart).
- Whether RCD protection exists on the target circuit; if not, what is needed.
- Certification and testing included or itemised separately.
- Fixed price or hourly estimate if wall access reveals unexpected obstacles.
For multiple outlets in a renovation, ask for a per-point breakdown. Bundled "10 power points — $3,500" quotes are hard to compare unless you know what is replacement versus new circuit work.
How 24/7 Service Mate handles power point installs
We assess the existing circuit, wall construction and board capacity before quoting. For straightforward replacements we often give a fixed price on the phone after a few questions. For new points in older Melbourne homes, we quote on site once we have confirmed a viable cable route.
We do not approve switchboard upgrades or new circuits without explaining why they are needed and what they add to the total. Every new installation is tested and certified where required before we leave.
Book through our power point installation service page or call for same-day availability in most Melbourne suburbs.
FAQ
- How much does it cost to add one power point in Melbourne?
- On an existing circuit with straightforward access, expect $300–$550. Through brick walls or across rooms, $450–$650+. Replacing an existing point is cheaper at $150–$300.
- Can I install a power point myself?
- Fixed wiring in Victoria must be done by a licensed electrician. DIY power point work is illegal and dangerous — and will fail a building inspection or pre-sale electrical check.
- Why is my quote higher than the ranges above?
- Common reasons: double-brick walls, no ceiling access, board needs an RCD or spare way, asbestos backing at the board, or after-hours attendance. Ask the electrician which variable applies to your job.
- Do I need a safety switch for a new power point?
- Yes — current standards require RCD protection on the circuit. If your home has no RCD on that circuit group, adding one is part of making the new work compliant.
- Should I upgrade all my power points at once?
- Not necessarily. Replace damaged or non-compliant outlets as needed. If you are renovating and walls are open, bundling multiple new points is cheaper than returning later. Plan the layout before the plasterer closes the walls.
Renovating and need outlets planned before the walls close? Call 1300 24 11 47 — we map circuit loads and quote every point before the plasterer arrives.
Related reading
Explore our Melbourne electrical services or see what is included in power point and dedicated circuit installation. For more practical detail, read Safety Switch Installation Cost Melbourne: RCD Pricing & Board Upgrades and Powerboard vs New Powerpoint Victoria: When Extra Outlets Need a Real Circuit.
Need practical help now?
Need extra powerpoints without DIY risk—book a Melbourne electrician price on 1300 24 11 47.