Split system air conditioner being checked in a Melbourne home
HVAC

AC blowing warm air in 35 degree heat - 4 fixes you can try, and when to call us

Andy · Licensed HVAC Technician 7 min read

AC blowing warm air in 35 degree heat: what to check

Infographic: AC blowing warm air in 35 degree heat: what to check.

If your AC is blowing warm air, check the thermostat mode, clean the return-air filter, clear debris around the outdoor unit, and give the system 10 minutes after restart. If it still blows warm, ices up, leaks water, trips power, or runs during extreme heat without cooling, call a licensed HVAC technician.

The short version

  • Confirm the system is set to Cool, not Fan, Dry or Heat.
  • Set the temperature lower than the room temperature and wait a few minutes.
  • Clean the return-air filter and check airflow at the indoor unit.
  • Clear leaves, bags and stored items from around the outdoor unit.
  • Restart once. If it still blows warm, stop guessing and book a technician.

When Melbourne heat climbs, an air conditioner that only blows warm air feels urgent fast. The good news is that a few common causes are safe to check yourself. The bad news is that some of the most common faults, like low refrigerant, failed capacitors and electrical issues, are not homeowner repairs.

This guide gives you the quick checks first, then the signs that the problem has moved beyond a filter or remote-control setting.

Why air conditioners blow warm air

An AC cools by moving heat from inside the home to outside. For that to work, the system needs correct settings, strong indoor airflow, clean coils, a working outdoor unit, healthy electrical components and the right refrigerant charge.

If any part of that chain fails, you may still feel air from the indoor unit, but it will not be cold. Sometimes the indoor fan is simply moving room-temperature air because the system is set to Fan. Sometimes airflow is so restricted that the coil cannot absorb heat properly. Sometimes the outdoor unit is not running, so heat cannot be rejected outside. In more serious cases, a leak, compressor fault, capacitor fault or control-board issue needs proper diagnosis.

Australian refrigerant handling is restricted. The Australian Refrigeration Council explains licensing for people who handle fluorocarbon refrigerants. If a system is low on gas, the fix is not just topping it up. A technician needs to find why it is low and decide whether repair is practical.

4 fixes you can safely try first

1. Check mode, fan setting and target temperature

Start with the remote. Make sure the system is set to Cool. Fan mode will blow air without cooling it. Dry mode can reduce humidity but may not feel cold. Heat mode is easy to select by mistake, especially after winter.

Set the target temperature several degrees below the current room temperature and give the system a few minutes. If the indoor fan starts but the outdoor unit never runs, the issue may be outside the simple settings.

2. Clean or replace the filter

A clogged filter is one of the easiest ways to make an air conditioner perform badly. Dust, pet hair and lint restrict airflow across the indoor coil. In heavy summer use, that can lead to weak cooling, longer run times and even ice forming on the coil or pipework.

Turn the unit off, open the front panel, remove the mesh filters, wash them gently, let them dry fully and reinstall them. Do not put wet filters back in. If you have a ducted system, check the return-air grille filter instead.

3. Clear the outdoor unit

The outdoor unit needs clear airflow to reject heat. If it is surrounded by leaves, weeds, storage tubs, fencing or dust, the system has to work harder. During a hot Melbourne day, that extra restriction can push the unit into poor performance or protection shutdown.

Clear loose debris and keep space around the unit. Do not dismantle panels. Do not pressure wash electrical areas. If the outdoor fan is not spinning while the system is calling for cooling, call for service.

4. Restart once and give it 10 minutes

After checking the settings, filters and outdoor clearance, switch the system off at the remote and isolator if you can do so safely, wait a few minutes, then restart. Give the system around 10 minutes to stabilise.

If the air still feels warm after that, avoid repeated resets. A fault code, breaker trip, burnt smell, water leak, ice on the lines, or outdoor unit that hums without starting points to a technical fault.

When warm air means you need a licensed technician

Call a technician if the outdoor unit is not running, the fan is not spinning, the system trips the power, the indoor unit leaks water, ice appears on the pipework, the air smells burnt, or the system keeps running without lowering the room temperature.

You should also call if the system cools for a few minutes and then turns warm again. That can happen when a component overheats, the coil freezes, a sensor fails or the compressor cannot keep running. For commercial sites, do not wait too long. A shop, office, clinic or restaurant without cooling can quickly become a staff, customer and equipment issue.

For broader cooling-efficiency advice, Energy.gov.au has useful guidance on heating and cooling choices. For a live no-cooling fault, though, the priority is getting a safe diagnosis.

What it costs in Melbourne

Pricing depends on the cause. A dirty filter or blocked outdoor unit may only need advice or a service. A failed capacitor, fan motor, sensor, drain issue, control fault or refrigerant leak can require parts, testing and return work if parts are not available immediately.

Cost also changes with access, split system versus ducted, after-hours timing, the age of the unit, and whether repair makes sense compared with replacement. A good technician should explain the likely cause, test results, repair option, replacement risk and price before you approve the work.

How 24/7 Service Mate handles no-cooling calls

When you call, we ask what type of system you have, what suburb you are in, what the indoor and outdoor units are doing, whether there is water, ice, noise, smell or a power trip, and whether the property is residential or commercial. That helps prioritise urgent failures and send the right support.

On site, the technician checks settings, airflow, filters, drainage, outdoor operation and electrical behaviour before recommending the next step. The goal is to restore cooling where practical, but also to tell you when an ageing or undersized system is becoming a repeat-failure risk. For urgent no-cooling support, start with our emergency HVAC repair service.

FAQ

Why is my split system on but not cooling?
The most common simple causes are wrong mode, dirty filters or blocked outdoor airflow. If those checks do not fix it, the fault may be refrigerant, electrical or compressor-related.
Can a dirty filter make AC blow warm air?
Yes. A blocked filter can reduce airflow enough that the system cannot absorb heat properly. It can also contribute to freezing and water leaks.
Is low refrigerant dangerous?
Low refrigerant usually means there is a leak or another fault. Refrigerant handling is restricted, so it needs a qualified technician rather than a DIY top-up.
Should I keep running the AC if it is not cooling?
If the system is blowing warm air, leaking, icing up, making unusual noise or tripping power, turn it off and arrange service. Running it can worsen some faults.
Do you handle after-hours AC repairs?
Yes. Call 1300 24 11 47 and describe what the indoor and outdoor units are doing so we can advise the next step.

For local help, see our Melbourne HVAC services, HVAC services in Glen Waverley and HVAC services in Box Hill. For the bigger summer-failure picture, read why AC stops cooling in summer.

Need cooling back fast?

Call 1300 24 11 47 and tell us your system type, suburb, and whether the outdoor unit is running. We will help you work out the safest next step.

Need a Melbourne hvac technician?

We're one call away — 24/7 emergency service, live answer, upfront pricing.