Ice on your AC refrigerant lines means evaporator temperature has dropped below freezing - usually airflow restriction (filter, indoor coil) or refrigerant problems. Switch the unit off, let it thaw fully, clean or replace the filter. If it ices again within a day, you have a refrigerant issue or metering fault that needs a licensed HVAC tech.
The short version
- Switch the unit off immediately. Running iced ruins the compressor.
- Let it thaw fully (1-3 hours). Don't chip the ice off.
- Check and clean the filter while it thaws.
- Restart in fan-only mode for 20 minutes before resuming cooling.
- If it ices again within 24 hours, call a licensed HVAC tech.
Cause 1 - Dirty filter (most common, easy fix)
A clogged filter restricts airflow over the indoor coil. With less warm room air crossing the coil, the refrigerant in the coil doesn't absorb enough heat - and the coil drops below freezing. Moisture in the air condenses on the coil and freezes, growing back along the suction line.
Fix: pull the filter out (front panel of split, or behind ceiling grille for ducted), vacuum it, wash with mild soapy water if washable, air dry, refit. Replace every 6-12 months if non-washable. Filter access is the single most ignored maintenance task on Melbourne air conditioners.
Cause 2 - Low refrigerant (requires a licensed tech)
If refrigerant is low (almost always from a slow leak, not "use over time" - AC systems are sealed), the evaporator pressure drops, the boiling point drops, and the coil ices. You can't fix this yourself. ARC licensing under Australian Refrigeration Council rules means only licensed techs can handle refrigerant - it's an offence, and rightly so given the global warming potential of refrigerants.
A leak detection plus regas is $350-$650 for a typical Melbourne split system. If the leak is at the indoor unit braze joints or the outdoor flares, repair is often viable. If the leak is in the wall pipe run, the cost climbs.
Cause 3 - Blocked airflow at indoor unit
Even with a clean filter, airflow can be blocked: dirty evaporator fins (years of dust), a slipped fan blade, furniture in front of the unit, or a return air vent blocked by a couch (ducted). The symptom is identical to a dirty filter.
Diagnosis: with the unit running, feel airflow at the supply outlets. It should be strong and continuous. Weak airflow with a clean filter means deeper cleaning of the coil, fan and ducting.
Cause 4 - Running AC when outside is too cold
Most splits are rated to cool down to about 18°C outdoor ambient. Below that, the head pressure can't be maintained correctly and you'll see icing. In Melbourne, this matters in autumn and spring when people run AC at night for white noise or habit, but the outdoor temp has dropped to 12°C.
Fix: switch to heating mode, or use fan-only. The unit is doing exactly what it's designed to do at low outdoor ambient temperatures.
Cause 5 - Faulty metering device (the one to never ignore)
The expansion valve (TXV) or capillary tube meters refrigerant into the evaporator. If it's stuck partly closed, the evaporator runs starved - too little refrigerant, very low pressure, freezing. If it's stuck open, you get flooding back to the compressor and risk slugging damage to the compressor itself.
This is the one that can write off an AC. The symptoms can look identical to a dirty filter at first, but won't resolve with cleaning. A licensed tech uses superheat and subcool measurements to confirm. Call same day if cleaning didn't fix it.
The correct thaw procedure
- Switch off at the wall controller AND at the isolation switch outside.
- Let it sit for 1-3 hours. Don't open windows wide - just let the room equalise.
- Place towels under the indoor unit. As ice melts, condensate drain may overflow.
- Once visibly dry, restart in fan-only mode for 20 minutes (this dries the coil before cooling resumes).
- Now switch to cool. Watch for re-icing over the next 24 hours.
Don't chip the ice off, don't pour hot water on the lines, don't use a hairdryer. You'll bend fins or crack pipework.
When to call vs when to wait
- Call now: Ice on lines plus zero airflow, compressor short-cycling on/off, repeated icing within 24 hours of thaw, signs of refrigerant oil at outdoor unit.
- Can wait until next-day: Filter clearly dirty, first time icing, room is unusually cold.
- Annual service catches this: Get split systems serviced every 12-18 months. Catches early refrigerant issues before they ice.
Melbourne-specific ice-up risk: cold snaps and overnight settings
Running AC in heating mode during a Melbourne cold snap
Melbourne winters regularly drop below 8°C overnight, particularly in the outer suburbs and elevated areas. Most reverse-cycle systems are rated to operate efficiently down to around 5°C ambient (some modern inverter units down to −15°C). But older non-inverter split systems running in cooling mode on a cold morning — for example, if a timer is set incorrectly — will ice up rapidly. Always ensure your system is set to heat, not cool, during winter.
What to do right now if your unit is iced up
Turn the unit off at the remote and leave it in fan-only mode (no refrigerant flow) for 30 minutes. This allows the evaporator coil to defrost. Do not attempt to remove ice with sharp objects. Once defrosted, run on fan-only for 5 minutes then restart in cooling mode. If ice forms again within an hour, the cause is refrigerant-related (not just airflow) and you need a licensed tech. A refrigerant top-up without diagnosing the leak first is a temporary fix only — the gas will escape again and the problem will recur.
FAQ
- Will running my AC with ice on it damage it?
- Yes. Icing causes liquid refrigerant to return to the compressor (slugging), which can destroy it. Switch off immediately.
- Can refrigerant leak slowly over years?
- Yes - micro-leaks at flares or braze joints lose 5-10% per year. The system may keep working but eventually drops below the icing threshold.
- Why does my AC ice in autumn but not summer?
- Lower outdoor ambient temps reduce the head pressure. A unit borderline on refrigerant will start to ice in mild weather before summer.
- Can I top up the refrigerant myself with a DIY kit?
- No. It's illegal in Australia without ARC licensing, and DIY mixing risks moisture contamination that destroys the system.
- How much does an AC regas cost in Melbourne?
- $350-$650 for a residential split. Commercial or VRV systems higher. Leak repair separate.
Related reading
For local help, see our Melbourne HVAC services, HVAC in Dandenong and HVAC in Glen Waverley. Our split system service and repair page covers regas, leak detection and annual servicing. For other AC issues, read AC blowing warm air in 35°C heat - 4 fixes you can try.
AC icing repeatedly?
Call 1300 24 11 47. ARC-licensed techs, leak detection and regas same day in most Melbourne suburbs.