Bathrooms combine water, steam and electricity. The closer an electrical item is to a shower, bath or basin, the more carefully the rating, location and protection must be checked.
Renovating a bathroom in Melbourne?
Call 1300 24 11 47 before waterproofing or tiling to plan compliant lights, fans and outlets.
The short version
- Bathrooms need electrical planning because water, steam and fixed wiring are a high-risk combination.
- The location of a shower or bath affects which fittings and IP ratings are suitable.
- Do not specify a towel rail, mirror or power point purely from a vanity drawing—its location and supply must be checked.
- Victorian fixed-wiring work requires a licensed electrician and a CoES where applicable.
What bathroom zones mean
Electrical rules divide wet areas into zones around baths, showers and basins. The zone affects what can be installed, how close it can be, and the IP rating required.
Common bathroom electrical items
| Item | What to check |
|---|---|
| Exhaust fan | IP rating, ducting and switch control |
| Downlights | Wet-area suitability and insulation clearance |
| Heated towel rail | Zone location and isolator |
| Power point | Distance from water and RCD protection |
Why IP ratings matter
IP ratings describe protection from solids and water. A fitting suitable for a dry hallway may be unsafe in a steamy bathroom or near a shower spray path.
The first digit describes protection against solid objects and the second describes water protection. For a homeowner, the useful takeaway is simple: the closer a fitting is to a bath or shower, the more specific its water-resistance rating and installation instructions need to be. “Bathroom style” on a retail label is not enough evidence that a fitting suits every location.
Authority links
Bathroom electrical work should follow wiring rules and building requirements. See Energy Safe Victoria and the National Construction Code for safety and building context.
Zone 0, 1 and 2 — what can go where
Bathroom electrical work is restricted by volume zones around baths and showers. Fixed appliances and outlets must match IP ratings and distances — not whatever fits the tile layout aesthetically.
- Zone 0 (inside bath/shower basin) — no low-voltage or mains fittings except listed immersed equipment
- Zone 1 — only approved fixed fittings such as shower-rated luminaires
- Zone 2 — IPX4 fittings; shaver outlets to AS/NZS 3112 if permitted
- Outside zones — standard GPOs with RCD protection still required
Zone dimensions and permitted equipment are technical matters under the applicable wiring rules, and the actual bathroom geometry matters. A freestanding bath, open shower, shower screen height, ceiling slope and bath position can change the assessment. Have the electrician work from a measured plan rather than relying on a generic online diagram.
Heated towel rails and exhaust fans
Hardwired towel rails and fans need correct zone placement and dedicated circuits where loading requires. DIY installs into cavity walls cause moisture tracking and trip faults.
An exhaust fan should be selected for more than its appearance. Check whether it vents outdoors, whether duct runs are practical and whether it needs a run-on timer or humidity control. A fan that merely recirculates moist air into a roof space can contribute to condensation problems. For towel rails, confirm whether the selected unit is plug-in or hardwired, its IP rating, cable entry and the required separation from water before the wall is sheeted.
Renovation tip
Electrical rough-in should be finalised before waterproofing — moving a non-compliant light after tiling is expensive.
Heated mirrors and underfloor heating
Both need correct IP rating and RCD protection. We coordinate with tilers so penetrations stay outside wet zones.
Underfloor heating needs early coordination: the heating mat, sensor, thermostat position and cable paths must be fixed before waterproofing and tiles. Heated mirrors also need a suitable mounting location and concealed supply planned before the wall lining closes. Leaving either item until fit-off can mean visible conduit or a change to the design.
Plan the electrical rough-in first
Bring the vanity, shower, bath, mirror and towel-rail selections to the electrical rough-in meeting. We can locate switches, fan controls, lights and outlets around the real fixtures, then coordinate with the builder, waterproofer and tiler. This avoids drilling a freshly waterproofed wall to correct a non-compliant position later.
Compliance and certification in Victoria
Energy Safe Victoria provides electrical safety information, while the National Construction Code gives relevant building context. A licensed electrician performs the fixed electrical work, tests the installation and provides a Certificate of Electrical Safety when required. Keep that documentation with renovation records; it is useful for future maintenance, sale and insurance questions.
FAQ
- Can a power point go beside a basin?
- Only where the required separation, location and protection requirements are met. Ask before cabinetry is installed.
- Can I install a heated towel rail myself?
- A plug-in unit may be mounted according to its instructions, but a hardwired rail and any fixed wiring require a licensed electrician.
- Can any downlight be used in a bathroom?
- No. The fitting must suit its zone, have an appropriate IP rating and be installed with the required clearances and insulation considerations.
- Why does my bathroom fan keep tripping the safety switch?
- Moisture, damaged wiring, a failed motor or an installation fault can cause this. Stop resetting it and arrange diagnosis.
- Do bathroom electrical jobs need a CoES?
- In Victoria, the licensed electrician provides a Certificate of Electrical Safety where the completed work requires one.
Good bathroom design is safer when it is planned
Choose fittings after their location, rating and supply have been checked. That protects the finished room, the people using it and the investment in your renovation.
Related reading
For local help, see our Melbourne electrical services, electrician in Richmond, electrician in Melbourne CBD. Our emergency electrician in Richmond page covers scope, pricing and 24/7 dispatch. Emergency? See our emergency electrician in Richmond. Related guides: Commercial electrical inspection Melbourne - compliance, test and tag, switchboard audits, Hardwired vs battery smoke alarms: which is compliant and safer?.