In Melbourne bathrooms, an exhaust fan manages moisture and mould risk; a heat lamp (or 3-in-1) adds radiant warmth for winter showers. They are not interchangeable. A heat lamp without extraction will not fix condensation on south-facing windows, and a strong exhaust alone will not make a tiled floor feel warm on a July morning.
Upgrading a bathroom ceiling?
Call 1300 24 11 47 — we install compliant exhaust and heat-lamp units with the right switching and ducting.
The short version
- Exhaust = moisture control. Prioritise it if you see mould, peeling paint or persistent steam.
- Heat lamp = comfort heat. Useful in cold bathrooms; does not replace ventilation.
- 3-in-1 units (light + heat + exhaust) are popular in Melbourne renovations when ducting can reach eaves or a suitable outlet.
- Typical install ranges often sit around $250–$700 for fan-only swaps, and $400–$1,200+ for heat or 3-in-1 with ducting — site dependent.
- Wet-area electrical zones and IP ratings matter — use a licensed electrician.
What bathroom exhaust actually does
Extraction removes humid air so moisture does not condense on ceilings, mirrors and wardrobes. Melbourne’s cooler months make condensation worse because indoor air hits cold surfaces. An undersized or ductless “fan” that only recirculates will not solve mould. Look for adequate airflow (L/s), a duct to outside, and a run-on timer so the fan continues after you leave.
Service context: exhaust fan installation Melbourne.
What heat lamps do (and do not do)
Infrared heat lamps warm people and surfaces quickly beneath them. They are excellent for short bursts of comfort. They do not dry the room the way extraction does, and leaving high-wattage lamps on as “heaters” wastes energy and can overheat fittings if the wrong lamps are used. Always match lamp type and wattage to the fitting’s rating.
Exhaust vs heat lamp vs 3-in-1
| Option | Best for | Watch-outs |
|---|---|---|
| Exhaust only | Mould, steam, code-minded ventilation | No radiant warmth |
| Heat lamp only | Comfort in already well-ventilated rooms | Won’t fix moisture |
| 3-in-1 combo | Most Melbourne family bathrooms | Needs space, duct path, correct switching |
| Heated towel rail (separate) | Drying towels + gentle warmth | Different circuit/load planning |
Typical Melbourne install cost guides
| Job | Typical range |
|---|---|
| Replace existing exhaust (same cut-out) | $250–$550 |
| New exhaust with duct to eaves | $450–$900 |
| Heat lamp or 3-in-1 replace existing | $400–$850 |
| New 3-in-1 with ducting + new switches | $700–$1,200+ |
Concrete ceilings, long duct runs, and two-storey roof access increase labour. Apartment rules may restrict roof penetrations — use wall vents where approved.
Electrical and wet-area rules
Bathrooms have zoning rules for fittings near baths and showers. Your electrician selects IP-rated equipment and switch positions that comply. Overview: bathroom electrical zones Victoria. Certification applies to new electrical work as required by Victorian regulations — see Energy Safe Victoria.
Mould first, warmth second
If black mould returns on the ceiling every winter, fix extraction and any building leaks before investing in more heat lamps. Heat without airflow can worsen moisture problems by warming wet air without removing it. Pair exhaust with habits: run the fan during and after showers, and leave the door ajar when safe for airflow.
How 24/7 Service Mate installs bathroom ventilation
Kevin checks the existing cut-out, duct path and switch arrangement, then recommends fan-only versus 3-in-1 based on your mould and comfort priorities. Related: lighting installation and electrical services.
Ducting details that decide real-world performance
Flexible duct that sags, is crushed by insulation, or runs excessively long kills airflow. Rigid or well-supported short runs to eaves or approved wall vents perform better. Discharging into the roof void is a classic false install: moisture condenses on cold roof steel and rains onto insulation. Insist on a true external termination and bird/insect screening that does not choke the fan.
For two-storey homes, upper bathrooms sometimes need longer vertical ducts — select fans with enough static pressure, not only a pretty faceplate.
Switch layouts that households actually use
Separate switches for heat, fan and light beat a single mystery toggle. Run-on timers for the fan should be explained at handover. Guests and teenagers will not run extraction if they cannot find the switch. In rentals and short-stays, label the switches discreetly.
Heat lamp circuits should match lamp ratings. Over-lamping a fitting is a fire risk. When replacing lamps, keep spares of the correct type in the laundry cupboard.
Pairing with broader moisture control
Extraction cannot beat a leaking shower membrane or unvented dryer blowing into the bathroom. If mould returns after a new fan, investigate building leaks and habits. Plumbing and electrical fixes often travel together in older Melbourne weatherboards.
Rental and strata bathroom upgrades
Landlords often approve exhaust first because mould claims are expensive. Heat lamps are comfort upgrades that still help winter reviews. In apartments, roof discharge may be banned — use approved wall vents and check OC rules before cutting. Document the install for the condition report.
3-in-1 sizing and cut-outs
Replacing a small exhaust with a larger 3-in-1 may need ceiling cut-out enlargement and patching. Factor plaster and paint if you want a neat finish. Concrete ceilings in some apartments limit options to surface or specially rated solutions — inspect before buying the fancy unit online.
Electrical load notes
Multiple heat lamps draw significant current. Confirm the lighting circuit can handle the load, especially in older flats where bathrooms share circuits with hallways. An electrician should verify, not a guess from the lamp packaging.
Mould remediation sequencing
Clean mould safely, fix leaks, install extraction that actually ducts outside, then consider heat lamps for comfort. Reversing that order — heat lamps first — wastes money. If paint keeps blistering after a new fan, call a plumber for membrane or grout failures rather than buying a stronger lamp.
Selecting low-noise fans
Noise ratings matter in apartments where the bathroom shares a wall with a bedroom. Look for quality bearings and suitable duct silencers where needed. A silent fan that moves no air is useless; balance sone ratings with L/s performance. Controllers with adjustable run-on help night use without hour-long drone.
Quick decision tree
See mould or heavy steam? Exhaust first. Freezing tiles but dry ceiling? Heat lamp or heated rail may be enough beside existing extraction. Want both comfort and dryness in one ceiling cut? 3-in-1 with real ducting. Still unsure? Book a site look — cut-out and duct path decide more than brochure photos.
After install, run a hot shower test and confirm steam clears within a few minutes with the door closed — that is the practical performance check.
FAQ
- Is a heat lamp enough ventilation?
- No. Heat lamps do not replace an exhaust path to outside.
- Do I need a separate light if I install a 3-in-1?
- Many 3-in-1 units include a centre light. Confirm lumen output if you want bright task lighting for grooming.
- Can I install this myself?
- Ceiling electrical work in wet areas should be done by a licensed electrician. Incorrect wiring is a shock and fire risk.
- Why does my exhaust make little difference?
- Blocked duct, fan discharging into the roof void, undersized unit, or no run-on time are common causes.
Related reading
Explore our Melbourne electrical services or see what is included in ceiling fan installation. For more practical detail, read Pool Pump Electrical Installation Melbourne: Circuits, Timers & Safety and Spa Electrical Requirements Victoria: Safety Switches, Bonding & Compliance.
Steam, mould or a freezing bathroom?
Call 1300 24 11 47 — get the right mix of exhaust and heat for your Melbourne bathroom, installed to wet-area rules.