Before booking a home EV charger install in Melbourne, answer three questions: does your switchboard have the spare capacity for a 7kW (single-phase) or 22kW (three-phase) charger; which charger type matches your car and weekly km; and where will the cable run from the board to the charger location. Together they decide whether the job is $1,800 or $4,500.
The short version
- Question 1: switchboard capacity. Most pre-2010 boards need an upgrade.
- Question 2: 7kW single-phase vs 22kW three-phase. Most homes only need 7kW.
- Question 3: where the cable runs from the board to the parking spot.
- Typical Melbourne install cost: $1,800-$2,800 (7kW). $3,500-$4,500 (22kW with three-phase upgrade if needed).
Question 1 - Does your switchboard support it?
A Level 2 home charger draws 32A (single-phase 7kW) or 32A three-phase (22kW). Both need a dedicated circuit and dedicated RCD protection - which means dedicated space on the switchboard. If your home was built before 2010 and the board has ceramic fuses or no spare ways, you're looking at a switchboard upgrade ($1,800-$3,500) before the charger even gets installed.
A load calculation also matters. A 5-bedroom home running ducted aircon, induction cooktop, oven, hot water, pool pump AND a 22kW EV charger may exceed the existing main supply rating. The electrician will run an after-diversity maximum demand (ADMD) calc to confirm before quoting.
Question 2 - What charger type do you actually need?
The honest answer: most Melbourne households only need a 7kW single-phase charger.
| Charger | Speed | Best for |
|---|---|---|
| Level 1 (granny, 2.3kW) | 10-15km/h | Plug-in hybrids, very low daily km |
| Level 2 single-phase 7kW | ~40km/h | Most EV owners, 30-200km daily |
| Level 2 three-phase 11kW | ~65km/h | Heavy daily users, multiple EVs |
| Level 2 three-phase 22kW | ~120km/h | Rare residential need, future-proofing |
| DC fast (Level 3 50kW+) | commercial only | Not a home install |
If you do 60km a day, a 7kW charger refills overnight in 2 hours. Spending an extra $2,000+ on three-phase to go faster doesn't change the result. The exception: multiple EVs sharing one charger, or a home where you genuinely top up between school runs.
Question 3 - Where will you run the cable?
Cable cost is per metre of cable plus the conduit/cable tray and any trenching, drilling or chasing. Scenarios:
- Garage attached to home, board on garage wall: 2-5m cable run. Cheapest install ($1,800-$2,400).
- Garage attached to home, board on opposite side: 8-15m via roof space or external conduit. Add $300-$600.
- Carport at front of house: 15-25m, sometimes underground conduit. Add $500-$1,200.
- On-street parking (rented or older inner-city): Often not legal/practical. Consider workplace charging or public charger access instead.
- Detached garage: Requires either dedicated supply from the main board or a sub-board. Add $800-$2,200.
Cost breakdown - charger unit + installation (Melbourne 2026)
| Component | Cost range |
|---|---|
| Charger unit (Wallbox, Tesla, Zappi, JET Charge, Schneider) | $1,100-$2,400 |
| Standard install 7kW (5-10m run) | $700-$1,400 |
| Switchboard upgrade if needed | $1,800-$3,500 |
| Three-phase upgrade if needed | $3,500-$8,500 |
| Long cable run (15-25m) | +$300-$900 |
| Sub-board for detached garage | +$900-$2,200 |
Rebates - what's available in 2026
The Victorian government's EV home charger rebate (when active - check Solar Victoria for current status) has previously offered up to $1,000 off install. Federal Small-scale Technology Certificates don't apply to EV chargers. Some networks (Jemena, CitiPower) run trial demand-management discounts for OCPP-compatible chargers that can be managed remotely. Always check current programs at the time of quote - this space moves quickly.
Charger brands compared
- Tesla Wall Connector: Best with Tesla, works with other EVs via adapter. $850-$1,100.
- Wallbox Pulsar Plus: Compact, app-controlled, OCPP. $1,400-$1,800.
- Zappi (Myenergi): Solar-aware, only charges from excess solar. $1,800-$2,400.
- JET Charge / Ocular: Australian-supported, network-managed. $1,300-$1,900.
- Schneider EVlink: Robust, used in commercial too. $1,500-$2,200.
How 24/7 Service Mate installs EV chargers
Process: on-site assessment (free for charger installs over $1,500), load calc, switchboard inspection, OCPP/integration check if you have solar, written quote with itemised costs. Install day: typically 4-7 hours including testing and commissioning. We register OCPP chargers for grid management programs where eligible. Compliance certificate issued and lodged with Energy Safe Victoria.
FAQ
- Can I install an EV charger myself?
- No. EV charger installation is licensed electrical work in Victoria. DIY is illegal and unsafe.
- Will my solar charge my EV for free?
- With a solar-aware charger (Zappi, Wallbox with PV integration), yes - excess solar charges the car instead of being exported. Without that integration, the car charges from whatever the grid provides.
- How long does install take?
- Simple installs 4-6 hours. With switchboard upgrade, 1-2 days.
- Do I need approval from my electricity distributor?
- For most 7kW single-phase chargers, no. For three-phase 22kW, yes - the distributor (Jemena/CitiPower/United Energy/Powercor) needs to approve and may request load management.
- Can I charge two EVs at once?
- Either two chargers or one charger with built-in load balancing. The smart-charging chargers can supply two cars sequentially.
Related reading
For local help, see our Melbourne electrical services, electrician in Glen Waverley and electrician in Hawthorn. Our switchboard upgrades page covers what often gets done at the same visit. For the switchboard side, read switchboard upgrade cost Melbourne 2026, EV charger types, EV charger load management, and home electrical load calculations.
Planning a home EV charger?
Call 1300 24 11 47. Free on-site assessment, load calculation, itemised quote.