The first hot week is when pads that sat dry all winter dump dust into the house, or a stuck dump valve floods the roof space. Spend twenty minutes on water, pads and the isolation switch before you run it on high.
The short version
- Do the start-up on a mild day in spring, not during the first heatwave.
- Check water supply, pads, pump, float valve and bleed or dump valve first.
- Isolate the power before you open a roof cabinet or touch the pump.
- Dust from the pads in the first hour is normal. Smell and dripping through the ceiling are not.
- Roof work and any wiring is for licensed tradespeople, not a ladder on a wet tile.
Why spring start-up fails
The first hot week is when pads that sat dry all winter dump dust into the house, or a stuck dump valve floods the roof space. Spend twenty minutes on water, pads and the isolation switch before you run it on high. A cooler that has been wrapped and shut down for months is a different machine from one that has run all summer. Pads harden, minerals bake onto the pump, float valves jam, and birds and insects move into the cabinet.
Common start-up failures we see in Melbourne:
- Pump seized after months dry, tripping the circuit.
- Float valve stuck open, flooding the sump and overflowing into the roof space.
- Pads crumbled or clogged with scale, causing a damp, musty smell inside. Related: evaporative cooler musty smell.
- Bleed line blocked, so mineral build-up coats everything.
- Belt slipping or bearings squealing on belt-drive models.
- Controller or wall switch not working because a winter rodent chewed a cable.
Owner checks vs licensed work
You can do: look at the outside of the cooler from the ground, check the water tap to the unit is on, switch the unit to fan-only for a few minutes to confirm airflow, then add water mode, and watch for leaks at the ceiling outlets. Clean or replace the filters at the internal grilles. Check that the roof cover or winter lid has been removed.
Licensed work: anything on the roof, the pump electrical, the isolator, the wall controller, the dump valve and any water connection. If you need to go on the roof, the ladder, harness and weather all matter. We will not send a technician onto a wet tile roof in the wind.
The step-by-step we follow: isolate power, open the cabinet, inspect the pads, clean the sump, check the pump spins freely, test the float valve, flush the bleed line, fit new pads if needed, reconnect, restore power, run fan-only then water, check each ceiling outlet, test the controller and look for leaks.
Pads, water and the bleed rate
Pads cool by evaporating water from a wet medium. Melbourne water is soft in most areas, but local scale still builds up. A bleed system sends a trickle of water to drain so the sump does not concentrate minerals. If the bleed is blocked, scale coats pads and the cooler loses performance and smells. If you have a dump valve model, it empties the sump on a cycle, and a stuck valve either never empties or never closes.
Pads usually last two to three seasons in Melbourne. If you see white crust, a rotten smell or sagging, replace them. Related: evaporative cooling problems and reverse cycle vs evaporative.
What to expect in Melbourne weather
Evaporative coolers shine on dry days. On a humid 32°C day they struggle, because the air cannot absorb more moisture. Open windows slightly in rooms you want cooled, to let air flow through, and close doors to rooms you are not using. Do not run it with every window shut: the house fills with damp air and cools poorly. Run it early in the day to pre-cool the house, rather than starting at 4 pm when the roof is at its hottest.
Cost guide for 2026
Guides only; we quote after inspection.
- Spring start-up service with a clean and test: typically one to three hundred dollars.
- Pad replacement: a few hundred dollars, depending on model and number of pads.
- Pump replacement: commonly a few hundred dollars with parts.
- Float valve, dump valve or bleed repair: a modest repair, often a call-out plus parts.
- Controller or wiring fault: priced after diagnosis; may involve an electrician.
- New evaporative system: priced by size, with a bigger spend for ducted models.
Winter shut-down matters
Good spring start-ups begin the previous autumn. Turn off the water, drain the sump and the pipework, turn off the power at the isolator, and fit a cover over the roof unit or the ducted ceiling grilles. A cooler left full of stagnant water over winter breeds algae and bacteria, and the first run in spring spreads that smell through the house. If your cooler was not shut down properly, a deeper clean and a sanitise of the sump is a sensible first step. Related: humidity and mould in aircon.
Check ceiling grilles inside the house too. Sealed ceiling closures that were left in place in winter have to be opened before the first run, or the fan will push against a shut door.
FAQ
- Should I run it on a 16°C Melbourne day to test?
- Yes. A mild day is the perfect time. If something leaks or sounds wrong, you can fix it before the heat arrives.
- Water in the ceiling after start-up. Emergency?
- Turn the cooler and the water supply off, and call. Water through plaster can sag and damage ceilings and light fittings quickly.
- Can I change pads myself?
- Some owners do. It needs roof access and care with the pump and wiring. Many choose to have it done at the same visit as a service.
- Bleed rate. What is that?
- A small constant water discharge that stops scale and salt building up in the sump. It is not a leak.
- East vs west suburbs?
- West of the city is drier and hotter, so coolers get more use but dust more. East and south-east suburbs are more humid, so refrigerated cooling often suits better.
- Is evaporative cooling cheaper to run?
- Usually yes, often a fraction of a reverse-cycle system, but it needs water and fresh air flow to work well.
Related reading
See HVAC, AC maintenance and tune-up, heatwave aircon checklist, HVAC in Werribee and HVAC in Essendon.
Evaporative cooler ready for summer?
Book a spring start-up before the heat. Call 1300 24 11 47.