Flickering lights are rarely just a nuisance. They point to one of five issues - most are minor, but two are genuine fire or safety risks. Start with the simplest cause and work down the list before calling an electrician.
The short answer
A single light flickering is almost always the fitting or bulb. Multiple lights flickering on the same circuit points to a loose connection. Whole-house flickering - especially when large appliances switch on - means a loose neutral at the switchboard or at the street connection, and that is a call-an-electrician-today fault.
Cause 1 - Loose or failing bulb
The most common cause and the easiest to fix. LED bulbs can flicker when:
- The bulb is not fully seated in the fitting.
- The bulb is incompatible with a dimmer (most LED bulbs need a trailing-edge or LED-rated dimmer).
- The bulb itself is failing - LEDs can flicker before complete failure.
What to check
Switch off the light, let the bulb cool, then reseat it firmly. If it flickers with a dimmer, test it without the dimmer or swap to a dimmer-compatible LED. If it still flickers, replace the bulb.
Cause 2 - Incompatible dimmer switch
Older leading-edge (TRIAC) dimmers were designed for incandescent bulbs drawing 40-60W. A modern LED drawing 6-9W sits below the dimmer's minimum load and flickers at low settings.
What to check
Check the dimmer's minimum load rating on the faceplate or datasheet. If your LEDs are below it, either install a load corrector (a small resistor that fools the dimmer) or replace the dimmer with an LED-rated trailing-edge model. Dimmer replacement is licensed electrical work in Victoria - book an electrician.
Cause 3 - Loose connection at the fitting or switch
Wires terminate at push-in connectors or screw terminals inside the ceiling rose or switch. Over years, thermal cycling loosens these. A loose active or neutral connection causes intermittent contact - which shows up as flickering, especially when the circuit is under load.
Warning signs of a loose connection
- Flickering gets worse when other appliances on the same circuit switch on.
- The light flickers when you walk near it (vibration breaks the intermittent contact).
- There's a faint ticking sound from the fitting.
Loose connections generate heat and can cause arcing - a fire risk. This is a job for a licensed electrician. Energy Safe Victoria identifies loose connections as one of the primary causes of residential electrical fires.
Cause 4 - Overloaded circuit
If you have a high-draw appliance (electric oven, pool pump, EV charger) on the same circuit as lighting, the voltage drop when the appliance starts up shows as a brief flicker. This is a design problem - lighting and high-draw circuits should be separated.
What to check
Note when the flickering happens. If it coincides with a specific appliance starting, the circuits are sharing capacity they shouldn't. An electrician can add a dedicated circuit for the high-draw appliance.
Cause 5 - Loose neutral at the switchboard or meter box
This is the most serious cause. A loose neutral - whether inside your switchboard, at the meter box, or at the street connection - causes voltage imbalance across circuits. Symptoms include:
- Multiple lights or rooms flickering simultaneously.
- Lights that dim or brighten as other appliances switch on or off.
- Appliances behaving strangely (clocks losing time, TVs resetting).
- Flickering that affects the whole house, not just one circuit.
A loose neutral can cause over-voltage events that destroy appliances and pose a fire risk. If you see these symptoms, switch off non-essential circuits at the board and call an electrician or your network provider (AusNet, Powercor, CitiPower, Jemena, or United Energy) immediately.
Quick diagnostic table
| Symptom | Likely cause | Action |
|---|---|---|
| One light, one fitting | Bulb or fitting | Reseat bulb, replace if needed |
| One light on a dimmer | Incompatible dimmer | Swap to LED dimmer (licensed work) |
| One room, multiple lights | Loose connection in circuit | Call electrician - same week |
| Flicker when appliance starts | Overloaded circuit | Electrician to add dedicated circuit |
| Whole house flickering | Loose neutral | Call electrician today - urgent |
Is flickering an emergency?
Whole-house flickering and flickering with burning smell or discolouration at fittings are same-day emergencies. Single-room flickering with no other symptoms is urgent but not emergency - book within a few days. A single bulb flickering is not urgent.
How 24/7 Service Mate diagnoses flickering lights
We attend flickering faults with a thermal camera and insulation resistance tester. The thermal camera finds hot spots in fittings, switches, and the switchboard that indicate loose connections before they become fires. We check neutral continuity at the board and test earth leakage on the circuit. Most single-circuit flickering faults are diagnosed and fixed in a single visit.
FAQ
- Can I fix flickering lights myself?
- Reseating or replacing a bulb is safe. Everything beyond that - working at the fitting, switch, or switchboard - is licensed electrical work in Victoria. Don't open ceiling roses or switch faceplates yourself.
- Why do my LED lights flicker but my old incandescent ones didn't?
- Incandescent bulbs have thermal mass - they smooth out brief voltage variations. LEDs respond almost instantly to voltage changes, making them more sensitive to loose connections and dimmer incompatibility.
- My lights only flicker at night - why?
- Evening is peak demand on the local network. Voltage variation from the grid is slightly higher at peak times, which reveals marginal connections that hold up fine at lower demand. If it's consistent every evening, worth investigating.
- How much does it cost to fix flickering lights in Melbourne?
- A dimmer replacement is typically $150-$250. Tightening loose connections in a fitting or at the board is $180-$350 depending on access. If a loose neutral requires switchboard or meter work, budget $350-$600. We provide upfront quotes before starting.
Related reading
For local help, see our Melbourne electrical services, electrician in Richmond, electrician in Melbourne CBD. Our emergency electrician in Richmond page covers scope, pricing and 24/7 dispatch. Emergency? See our emergency electrician in Richmond. Related guides: Ceiling fan installation cost Melbourne 2026, Circuit breaker keeps tripping: appliance fault, circuit overload or wiring problem?.