Gas Heater Not Working? 7 Things to Check Before Calling
Heating & Cooling

Gas Heater Not Working? 7 Things to Check Before Calling

24/7 Service Mate · Heating and cooling advice team 8 min read

Gas Heater Not Working?

Infographic: Gas Heater Not Working?
Melbourne\

Melbourne's gas ducted heaters get a hard workout from April to September. When yours stops working mid-winter, the first instinct is to call a technician immediately — but several common faults are either self-diagnosable or have a simple reset fix. Here are 7 things to check before booking a call-out.

⚠️ Smell gas? Don't troubleshoot — act immediately:

  1. Turn off gas at the meter
  2. Open windows and doors
  3. Don't operate any switches
  4. Leave the building
  5. Call 1800 GAS VIC (1800 427 842) from outside

Melbourne's gas ducted heaters get a hard workout from April to September. When yours stops working mid-winter, the first instinct is to call a technician immediately — but several common faults are either self-diagnosable or have a simple reset fix. Here are 7 things to check before booking a call-out.

Check 1: Is the gas supply on?

Before anything else, confirm the gas supply is active:

  • Check the gas meter at the front of the property. The valve handle should be parallel to the pipe (on), not perpendicular (off)
  • Test another gas appliance — kitchen cooktop, hot water system. If those don't work either, contact your gas retailer
  • Check your gas bill is not overdue — disconnection for non-payment is more common than most realise

Check 2: Thermostat and mode settings

This sounds obvious but is the single most common call-out cause:

  • Is the thermostat set to HEAT (not COOL or FAN ONLY)?
  • Is the set temperature above the current room temperature?
  • Has the thermostat battery been replaced? Most wall thermostats use AA batteries; a flashing battery icon or blank screen means replace first
  • For smart/WiFi thermostats: is the app showing a connection error that might indicate the controller lost its pairing?

Check 3: Power to the unit

Gas ducted heaters still need electricity to power the fan, controls, and igniter. Check:

  • The dedicated circuit breaker for the heater at the switchboard (often labelled "HVAC", "AC" or "Ducted")
  • The ON/OFF switch near the unit itself (often on the wall near the ceiling-mounted unit)
  • An overheated or shorted unit may trip its own internal thermal fuse — this requires a technician

Check 4: Error or fault code on the display

Most modern ducted heater controllers (Brivis, Rinnai, Braemar) display error codes when a fault is detected. Look up the code in your unit's manual or the manufacturer's website. Common codes:

Display codeLikely meaning
E1 / F1Flame failure — ignition attempt failed
E2 / F2Limit switch tripped — unit overheated
E3 / F3Flue fault or pressure switch error
E7Fan fault — motor failure or blocked airflow
Flashing "WAIT"Normal — unit is in ignition retry sequence, wait 3–5 min

Check 5: Blocked or dirty filter

A severely blocked return air filter causes the unit to overheat and trip its thermal limit switch. The unit shuts down and won't restart until cooled. Check the filter (behind the ceiling grille or at the unit), clean or replace it, then try the reset procedure (see Check 6).

Check 6: Reset procedure

After checking power, settings, and the filter, try a full power cycle:

  1. Turn off the controller
  2. Switch off the circuit breaker at the switchboard
  3. Wait 2 minutes
  4. Restore power and set the controller back to heat mode

If the unit starts and then stops again within minutes, there is an underlying fault requiring a technician.

Check 7: Pilot light (older units)

Ducted heaters manufactured before approximately 2005 often have a standing pilot light rather than electronic ignition. If the pilot has gone out (draught, gas interruption, thermocouple failure), the unit won't fire. Relighting procedures are in the unit manual — but thermocouple replacement requires a licensed gasfitter.

When to stop checking and call a technician

  • Any gas smell — stop immediately and follow the gas emergency protocol above
  • Unit lights and fires but blows cool air — heat exchanger or gas valve fault
  • Fault code that doesn't clear after reset
  • Unit runs for 5–10 minutes then shuts off repeatedly
  • Yellow or orange flame visible — combustion problem requiring immediate service

Melbourne gas heater fault guide by symptom

Heater turns on but shuts off after a few minutes (short cycling)

Short cycling — the heater ignites, runs briefly, then shuts off and tries to restart — is one of the most common gas heater faults in Melbourne. Common causes include: a dirty or blocked return air filter reducing airflow over the heat exchanger (the heat exchanger overheats and trips the high-limit switch), a cracked heat exchanger (combustion gases mix with the airstream, triggering the safety cutout), a faulty flame sensor, or a blocked condensate drain on a condensing unit.

The dirty filter cause is a DIY fix — locate the return air grille (usually a large grille in a central hallway ceiling), remove the filter panel, vacuum or wash the filter, and reinstall. If the heater still short-cycles after a clean filter, call a licensed gas tech. A cracked heat exchanger is a safety issue and the heater must not be run until repaired.

Heater shows fault code on controller

Modern ducted gas heaters display fault codes on the wall controller or on the unit itself. Common codes for Melbourne brands (Brivis, Braemar, Bonaire, Rinnai):

  • Brivis codes E1, E2: Ignition failure (flame not established) — check gas supply, pilot, igniter
  • Braemar E3: Pressure switch fault — blocked flue or fan fault
  • Rinnai fault flash: Consult the unit label for flash sequence meaning

Always note the fault code before calling — it significantly speeds up the diagnosis. 24/7 Service Mate’s technicians carry common spare parts for Brivis, Braemar, Bonaire, and Rinnai systems for same-day repairs on most common faults.

No gas to the heater at all

If no gas appliances in the house work (check the stove or hot water system), contact your gas retailer (AGL, Origin, Jemena) to check for a supply interruption. If only the heater is affected, check the isolation valve at the heater unit is open (handle parallel to pipe = open, perpendicular = closed). If gas supply is confirmed and the unit still won’t ignite, the issue is inside the heater and requires a licensed technician.

When to call 24/7 Service Mate for your Melbourne gas heater

If your gas heater is not working and any of the following apply, call 24/7 Service Mate on 1300 24 11 47 rather than attempting further DIY diagnosis: the unit shows a fault code; you can smell gas near the heater (if you smell gas, turn off the heater, open windows, and call the gas emergency line 132 771 before anything else); the heater produces unusual smells like burning, smoke, or a faint exhaust odour; or the heater has not been serviced in more than 2 years. Our Melbourne-based team covers all Melbourne suburbs with same-day and after-hours call-out. Andy and the HVAC team carry common parts for Brivis, Braemar, Bonaire, and Rinnai units for fast turnaround on most repairs.

Annual gas heater servicing by a licensed technician typically costs $150–$250 in Melbourne and significantly reduces the likelihood of an unexpected breakdown on Melbourne’s coldest winter mornings.

FAQ

How much does it cost to repair a gas heater that won't start in Melbourne?
Diagnosis call-out: $150–$250. Common repairs: thermocouple ($200–$350), gas valve ($350–$600), PCB/control board ($400–$700). If repairs exceed 60% of replacement cost and the unit is 10+ years old, replacement is usually better value.
Can I do anything to prevent my heater from failing mid-winter?
Annual pre-season service (April–May) by a licensed gasfitter is the single best preventive action. It identifies developing faults before they cause a failure. See our ducted heating service cost guide.

Gas heater not working? We're available 24/7

Licensed gasfitters across Melbourne — same-day emergency and scheduled bookings. Call 1300 24 11 47.

For local help, see our Melbourne HVAC services, HVAC technician in Richmond, HVAC technician in St Kilda. Our gas heating installation and repair page covers scope, pricing and 24/7 dispatch. Emergency? See our emergency HVAC repair in Richmond. Related guides: Gas heater service Melbourne: how often, what's checked, and the legal CO test, Carbon Monoxide and Gas Heaters: Victorian Safety Rules and Detection Guide.

Need a Melbourne heating & cooling technician?

We're one call away — 24/7 emergency service, live answer, upfront pricing.