A partial power outage — fridge dead, lights on, or one side of the home dark while the street looks fine — is usually a property-side fault or a single protective device trip, not a full network blackout. Melbourne’s mix of single-phase houses and older multi-circuit boards makes “half power” a common emergency call.
Half the house without power?
Call 1300 24 11 47 — Melbourne electricians diagnose partial outages and restore circuits safely.
The short version
- If neighbours still have power, start at your switchboard — not the social media outage map alone.
- Partial loss often means one RCD/MCB tripped, a loose neutral/active issue, or a failed circuit — not always the whole service.
- Check safety switches and breakers once; do not hammer resets into a burning smell.
- Lost kitchen/laundry with lights OK is a classic RCD or circuit pattern.
- Call a licensed electrician if resets fail, trips repeat, or anything smells hot.
Partial outage vs full street blackout
| Observation | Likely domain | Next step |
|---|---|---|
| Street dark, neighbours dark | Network / storm | Check DNSP outage info; still inspect board for damage after storms |
| Street lit, neighbours OK, you partial | Your installation | Board triage + electrician |
| Only one room dead | Local circuit / fitting | See one room out guide |
| Lights dim + appliances dead unevenly | Possible serious supply imbalance | Urgent electrician — risk to appliances |
Safe switchboard triage
- Open the board cover carefully; use a torch if needed.
- Note which breakers/RCDs are in the tripped middle/off position.
- Unplug high-load appliances on dead circuits (heaters, kettles, dryers).
- Reset once. If it holds, monitor. If it trips again immediately, leave off.
- If the main switch is off and will not hold, do not force it — call urgently.
- Smell burning or see scorch? Stop. Isolate if safe. Call emergency electrician / 000 if fire.
⚠ Repeated instant trips
An RCD that will not reset usually means an active fault (moisture, damaged cable, failed appliance). Resetting ten times does not fix it and can increase damage.
Common Melbourne causes of partial power loss
- RCD trip on power circuits leaving lights on a separate non-RCD or different RCBO group.
- Failed RCBO protecting kitchen/laundry.
- Loose connection in board or junction after heat or vibration.
- Water in outdoor meter box after storms — coastal and weather-exposed panels.
- Off-peak / controlled load quirks on hot water circuits mistaken for “half house” faults.
- DIY renovations that shared neutrals incorrectly between circuits.
Doncaster, Frankston and similar suburbs with storm exposure see water-related partial outages; inner terraces see overloaded shared circuits after kitchen upgrades.
Appliance and food safety while you wait
- Keep fridge/freezer closed if that circuit is dead.
- Do not run generators indoors or back-feed the board — illegal and lethal to line workers.
- Medical equipment dependence = escalate to emergency priority on the phone.
What the electrician diagnoses
We identify which protective device and circuit failed, test for earth leakage, inspect the board for heat damage, and separate appliance faults from wiring faults. Sometimes the fix is a single RCBO; sometimes it is a wet outdoor board or a hidden junction. You get a make-safe plan and a written quote for anything beyond immediate repair.
Labelling and photos that speed diagnosis
A clear switchboard legend turns a 40-minute hunt into a 10-minute confirmation. If labels are missing, photograph the board with tripped devices before resetting and text it to the electrician. Note which rooms died: kitchen benches, hot water, outdoor power, lights only, or odd combinations. Off-peak hot water circuits confuse many homeowners into thinking “half the house” failed when only the controlled load is down.
For apartments, ask building management whether common-area outages or riser issues are reported. Sometimes multiple lots lose the same phase pattern during network events.
Medical, food and work-from-home priorities
Say on the first call if power loss affects medical devices, refrigerated medicine, or required work equipment. That changes dispatch priority and temporary advice. Generators must never back-feed a board — illegal and lethal. Transfer switches and proper generator inlets are planned electrical work, not emergency improvisation.
If fridge circuits can be temporarily fed from a known good circuit via a single heavy-duty lead as a short interim measure, ask the electrician first — random extension-lead webs create new hazards.
When partial outages repeat
Recurring partial losses after rain, heatwaves or when the oven starts point to underlying defects: moisture, overload diversity, or failing protective devices. Logging dates and triggers builds the case for board upgrades rather than endless reset theatre. Pair this article with our guides on night RCD trips and lights dimming under aircon start.
Single-phase quirks and odd room combinations
Homes can lose kitchen power and laundry power together while bedrooms stay lit because those rooms share an RCD group. Conversely, a failed RCBO may kill only outdoor power and the garage — which people describe as “half the house” if that is where they notice first. Walk every room with a phone torch checklist before you call; accurate mapping saves a return visit.
Three-phase properties and small commercial tenancies can lose one phase and keep others — lights may look normal in some areas while motors hum badly or not start. Mention if you have three-phase supply. Severe imbalance can damage equipment; treat it as urgent.
After restoration, test fridge, hot water and any sump pumps. Partial outages that coincide with rain should trigger a meter box moisture inspection even if power returns after a single reset.
Working from home when only some circuits die
Partial outages are uniquely annoying for hybrid workers: the lights work, the kettle works, but the study circuit or NBN cupboard is dead. Map which outlets feed routers and desktop machines and say so on the call — restoring communications can be prioritised within make-safe limits. Do not run unsafe extension webs across hallways as a week-long workaround.
Home offices in garages often sit on outdoor or garage circuits that trip first after rain. That pattern points to moisture or weatherproofing defects covered in our water-in-board and meter-box articles. Fixing the environment stops the “weekly partial outage” lifestyle.
If power returns after a reset but voltage feels “weird” — lights too bright, electronics resetting — treat that as urgent imbalance or loose-neutral territory, not a success story.
FAQ
- Why do lights work but power points do not?
- Many Melbourne boards separate lighting and power onto different RCDs/MCBs. A power-side RCD trip leaves lights on.
- Could it be the power company’s problem?
- Yes if the service fuse or network side failed. Electricians can help determine the boundary; network faults go to your distributor. Do not open sealed network equipment.
- Is partial power dangerous to electronics?
- Severe imbalance or loose neutrals can damage appliances. If lights are unusually bright/dim across rooms, treat as urgent.
- Should I reset the main switch first?
- Only if everything is off and guidance suggests it — usually start with the individual tripped device. When unsure, call before experimenting.
- Same fault every rainy day?
- Classic moisture ingress pattern. Needs inspection of outdoor gear and wet-area circuits, not endless resets.
Related reading
Explore our Melbourne electrical services or see what is included in electrical fault finding and repairs. For more practical detail, read Safety Switch Trips at Night Melbourne: Finding the Fault That Keeps Cutting Power and Sparks from a Powerpoint Melbourne: Causes, Risks & Same-Day Fixes.
Half power still deserves a full diagnosis
Call 1300 24 11 47 — we find which circuit failed and why, across Melbourne suburbs day and night.