When an RCD trips the moment you reset it - with nothing plugged into any outlet - the fault is not in a portable appliance. It's in the fixed wiring or a permanently wired appliance. This means you need an electrician, but the isolation steps below will help identify the circuit and let you restore power to the rest of your home while you wait.
First: understand what an RCD actually detects
A residual current device (RCD or safety switch) monitors the difference between current flowing out on the active conductor and returning on the neutral. Any difference above 30 mA - the threshold mandated in Australia - means current is going somewhere it shouldn't: to earth, through a fault in wiring or equipment, potentially through a person. The RCD trips to stop it.
When nothing is plugged in and the RCD still trips, the fault is generating 30+ mA of earth leakage without any portable load. That means the fault is in:
- The fixed wiring itself (damaged insulation, moisture ingress, a damaged joint).
- A permanently hardwired appliance (oven, cooktop, dishwasher, rangehood, hot water system, air conditioner, bathroom exhaust fan).
- The switchboard wiring or the RCD itself (faulty device - uncommon but possible).
Isolation steps: narrow down the fault circuit
Your switchboard will have one or more RCDs each covering multiple MCB circuits. Follow these steps to isolate which circuit is causing the trip:
- At the switchboard, turn off all MCBs under the tripped RCD.
- Reset the RCD. If it trips again immediately with all MCBs off, the fault is in the switchboard wiring or the RCD unit itself - stop and call an electrician immediately.
- If the RCD resets with all MCBs off, turn on MCBs one at a time. The RCD will trip again when you turn on the faulty circuit's MCB. Now you know which circuit to leave off.
- Leave that circuit MCB off, restore all other MCBs, and call an electrician to investigate the faulty circuit.
Note: If the faulty circuit is your only circuit (one RCD covering everything) or the circuit powers essential equipment like a medical device, call 1300 24 11 47 for an immediate dispatch. Do not keep resetting - repeated resets without fixing the fault can worsen the damage to wiring insulation.
Moisture ingress as a cause
Melbourne's weather drives moisture into unexpected places. Common scenarios:
- An outdoor outlet or garden light where water has entered the fitting.
- A bathroom exhaust fan or light fitting where condensation has accumulated inside the fitting.
- An underground or slab cable with a cracked conduit that has allowed water in over time.
- A pergola or garden shed outlet that has been exposed to rain or garden irrigation.
Moisture-related faults often disappear temporarily once the fitting dries out - the RCD resets and stays on for days before tripping again in wet weather. This pattern is diagnostic of moisture ingress and should not be ignored.
Hardwired appliance faults
Ovens, dishwashers, rangehoods, ducted air conditioners, and continuous hot water systems are all hardwired and remain connected to the circuit even when "off". A fault in any of these will show up as an RCD trip with nothing portable plugged in. The MCB isolation test will identify the circuit. From there, the electrician will use a megohmmeter (insulation resistance tester) to identify which part of the circuit is faulty - wiring or the appliance itself.
What the electrician will do
Energy Safe Victoria requires that electrical faults be assessed and rectified by a licensed electrician. The diagnostic process for a persistent RCD trip with no portable load involves:
- Confirming your isolation findings (which MCB triggers the trip).
- Insulation resistance testing on the identified circuit - measures how much current leaks through degraded insulation.
- Disconnecting hardwired appliances on the circuit to determine if the fault is in the wiring or an appliance.
- Visual inspection of accessible cable runs, especially in wet areas and outdoor locations.
FAQ
- Is it safe to leave the faulty circuit off and use the others?
- Generally yes, as long as the fault is confirmed to a single circuit and that circuit's MCB is turned off. The other circuits continue to operate normally under RCD protection. If you're unsure about the scope, call an electrician.
- Could the RCD itself be faulty?
- RCDs do fail, though it's not common. If the RCD trips with all MCBs turned off, the device itself or the wiring immediately behind it is the fault source. An electrician can test the RCD with a calibrated tester to confirm it's operating within specification.
- My RCD trips randomly - not always immediately. What does that mean?
- Intermittent trips suggest a fault that worsens under load, temperature, or moisture. Common causes: a connection that's loose and arcing under load, moisture-ingress faults that are worse in wet weather, or wiring with marginal insulation that leaks more at operating temperature. These need prompt investigation - intermittent faults don't resolve themselves.
- How much does it cost to find and fix a wiring fault in Melbourne?
- Diagnostic charge: $150–$280. If the fault is in a hardwired appliance, that appliance may need to be repaired or replaced by the relevant tradesperson. If it's in fixed wiring, rectification depends on access - a simple exposed junction fix is $200–$400; running new cable to replace a damaged section is $500–$1,500+.
Related reading
For local help, see our Melbourne electrical services, electrician in Richmond, electrician in Melbourne CBD. Our switchboard and safety switch upgrades page covers scope, pricing and 24/7 dispatch. Emergency? See our emergency electrician in Richmond. Related guides: Power point keeps tripping the safety switch - diagnosing the cause yourself, Circuit breaker keeps tripping: appliance fault, circuit overload or wiring problem?.