Licensed Melbourne HVAC technician removing a split system air conditioner with refrigerant recovery equipment
Heating & Cooling

Split system removal cost Melbourne 2026: decommission, refrigerant recovery and make-good

Andy · HVAC Technician 7 min read

Split system removal cost Melbourne: the short version

Infographic summarising the key points of Split system removal cost Melbourne 2026: decommission, refrigerant recovery and make-good.

Split system removal in Melbourne typically costs $250–$450 for a standard single-storey decommission with refrigerant recovery, $350–$650 when access is difficult or electrical isolation is required, and $500–$1,200+ when wall patching, crane hire or multi-head systems are involved. The price is driven by height, refrigerant type, pipe run length, make-good scope and whether the unit is being removed for replacement or permanent decommission.

Removing an old split before a new install or renovation?

Call 1300 24 11 47 — licensed refrigerant recovery and written pricing before units come off the wall.

The short version

  • Standard split system removal (single head, ground-access outdoor): $250–$450 in Melbourne.
  • Two-storey or restricted access outdoor unit: $350–$650.
  • Multi-head system removal (2–3 indoor units): $450–$900.
  • Refrigerant recovery is mandatory — must be included, not skipped.
  • Wall patching, electrical isolation and disposal are often extra unless itemised upfront.

Why split removal is regulated work — not a handyman job

Air conditioners contain refrigerant governed by Australian ozone protection and synthetic greenhouse gas regulations. Releasing refrigerant to atmosphere during removal is illegal and environmentally harmful. Removal must include recovery into a licensed cylinder by a technician with appropriate refrigerant handling credentials.

The electrical isolator, outdoor unit fixing, interconnecting cable and pipework also need safe disconnection. In Victoria, fixed electrical isolation work may involve a licensed electrician depending on scope — many HVAC companies coordinate both trades.

If you are replacing with a new split, removal and install are often quoted together — but the removal scope should still be separable on the invoice so you can compare if you are only decommissioning. See air conditioning installation for replacement paths.

Split system removal costs Melbourne 2026

Job Typical Melbourne range Main cost variable
Single split — standard access$250–$450Pipe run length, unit weight
Single split — 2nd storey / restricted access$350–$650Height, scaffold, harness work
Multi-head (2 indoor units)$450–$700Pipe chase, outdoor size
Multi-head (3+ indoor units)$600–$900+Complex pipe routes
Refrigerant recovery (included above)IncludedMust not be quoted separately as optional
Electrical isolator removal / cap-off$120–$280Board work, compliance
Wall penetration patch (basic)$150–$400Render match, paint excluded
Crane or hi-ab hire (rare)$800–$2,500+Roof-mounted, inner-city access
Responsible disposal / recycling$50–$150Council fees, refrigerant record

Ranges cover licensed removal and recovery. Make-good to invisible finish, structural repairs and new installation are additional.

What affects split system removal price

Access and height

Ground-level outdoor units on a suburban driveway in Cranbourne or Pakenham are a two-person lift. A condenser on a second-floor bracket overlooking a laneway in Fitzroy needs harness work, possibly scaffold — time and equipment move the price.

Refrigerant volume and type

Older R22 systems (being phased out) and larger ducted splits hold more refrigerant — recovery takes longer and attracts higher disposal tracking costs. Recovery time is usually bundled, but undersized quotes that skip recovery are a compliance red flag.

Pipe run and chase

A 3-metre pipe run through a single wall is quick. A 15-metre run through multiple rooms, or copper buried in rendered walls, adds labour to pull, cap and leave the cavity safe. Renovation projects sometimes leave pipes in walls intentionally — discuss retention vs full removal with your builder.

Wall make-good variables

Indoor unit removal leaves mounting plate holes and often a 70–80 mm penetration for pipes. Basic patch and sand is a small line item. Colour-matched render on a 1940s weatherboard in Williamstown, or large-format tile repair in a Southbank apartment, is a tiler or plasterer's scope — not always the HVAC technician's.

Quotes should state make-good level: "patch holes only" vs "paint-ready" vs "cosmetic finish excluded."

Replacement vs decommission only

Removal ahead of a new install on the same wall may reuse the penetration — cheaper than full make-good now and new penetration later. Permanent decommission for a switch to ducted gas or evaporative cooling needs complete cap-off and safe isolation.

Electrical scope

The outdoor isolator must be safely disconnected. If the circuit will not be reused, capping at the board may be needed. Electrical work should be itemised and performed by appropriately licensed trades. For broader electrical pricing see electrician cost Melbourne.

Removal as part of replacement — what to ask

Most Melbourne homeowners remove because they are upgrading. Ask:

  • Is removal included in the install quote or separate?
  • Will the same pipe penetration be reused?
  • Is electrical isolator upgrade included for the new unit's supply requirements?
  • Who patches the wall if the new indoor unit is a different size or position?
  • Is old unit disposal included?

See multi-head split system cost Melbourne for upgrade pricing context.

What a fair removal quote should include

  • Number of indoor and outdoor units being removed.
  • Refrigerant recovery and disposal documentation.
  • Access method for height — scaffold or harness if needed.
  • Electrical isolation scope and who performs it.
  • Pipe and cable removal extent — full pull vs cap-and-leave.
  • Make-good level and explicit exclusions (tiling, painting, render colour match).
  • Disposal fees and any council requirements.

Be wary of quotes under $150 for "split removal" with no mention of recovery — that is not compliant decommissioning.

How 24/7 Service Mate handles split removals

We recover refrigerant before any unit is disconnected — every time. We quote access, electrical cap-off and disposal separately from cosmetic make-good so you know what you are paying for before holes are patched.

If removal is ahead of a new install, we coordinate both scopes and flag when reusing pipe penetrations saves money. If you are renovating, we align timing with your builder so walls are not patched twice.

See split system service and repair, heating and cooling replacement, and Melbourne HVAC services.

FAQ

How much does it cost to remove a split system in Melbourne?
Standard single-split removal with refrigerant recovery typically costs $250–$450. Difficult access and multi-head systems cost more.
Can I remove an air conditioner myself?
Not legally or safely — refrigerant must be recovered by a licensed technician. DIY removal risks fines, injury from weight and height, and incomplete electrical isolation.
Is refrigerant recovery included in removal quotes?
It must be. If a quote does not mention recovery, ask directly. Recovery is not optional.
Who patches the wall after the indoor unit comes off?
Depends on the quote. Basic patching may be included; invisible finish usually needs a plasterer or painter — confirm exclusions before booking.
Should I remove the old split before buying a new one?
Usually quote removal and install together — the installer can often reuse penetrations and isolator positions, saving make-good cost.

Renovating and unsure whether to cap pipes or pull them? Call 1300 24 11 47 — we quote removal and make-good separately so your builder knows what is left in the walls.

Explore our Melbourne heating and cooling services or see what is included in split system service and repair. For more practical detail, read Portable AC vs Split System Melbourne: Cost, Comfort & When to Upgrade and Multi-Head Split System Cost Melbourne: Room-by-Room Cooling Pricing.

Need practical help now?

Removing an old split the right way protects the next install—book Melbourne HVAC removal on 1300 24 11 47.

Need a Melbourne heating & cooling technician?

We're one call away — 24/7 emergency service, live answer, upfront pricing.