Licensed Melbourne electrician inspecting a switchboard
Electrical

Outdoor lighting installation cost Melbourne 2026: garden lights, sensors and the weatherproof circuit

Kevin · Licensed Electrician 5 min read

Outdoor lights fail when they are treated like indoor downlights with a hole in the wall. They need weatherproof fittings, the right IP rating, and RCD protection. Price the circuit, not just the pretty lamp.

The short version

  • Price the circuit, not just the lamp. Cable, trenching and protection are where the cost sits.
  • Outdoor fittings need a suitable IP rating and must be on RCD-protected circuits.
  • Wall lights are cheaper than a garden circuit with low-voltage transformers and buried cable.
  • Sensors, timers and smart controls add a little cost and save a lot of annoyance.
  • Bayside homes need marine-grade fittings or they corrode in a season or two.

Wall lights vs garden circuits

Wall lights bolted to brickwork near the door are the simplest job. Power is nearby, the cable runs inside the wall or roof space, and the fitting is weatherproof. A garden circuit with path lights, uplights on trees and a feature wall is a different project: it needs a transformer (if low-voltage), buried cable in conduit or direct-burial rated cable, and a switch or timer back inside. The design stage matters, because moving a trench is more expensive than moving a lamp.

Think about where you walk, where the neighbours’ windows face and where the bin goes. A good scheme lights the path and the entry first, then adds feature lighting if the budget allows. See also home security installation if lighting is part of a wider safety plan.

Cost drivers

  • Number of points: every extra lamp is another cable run and termination.
  • Cable route: through a brick wall, under a path, across a lawn or along a fence changes labour a lot.
  • Fitting quality: stainless or marine-grade fittings cost more than painted aluminium, and last longer near the bay.
  • Control: a plain switch, a photocell, a timer, a motion sensor or a smart switch. Related: smart switch installation.
  • Power source: a nearby board with spare ways, or new circuit all the way from the main switchboard.
  • Existing wiring condition: old unprotected outdoor circuits get upgraded as part of the job.

Compliance

Outdoor lights are in a wet location, so fittings must have a suitable ingress protection rating (IP rating) for where they sit: under an eave, in the open, or close to a pool. The circuit needs RCD protection, which a modern switchboard provides. If your board has only old ceramic fuses or no safety switches, we upgrade that before adding outdoor load. In Victoria the work is prescribed electrical work, so you receive a Certificate of Electrical Safety. Related: Certificate of Electrical Safety.

Lights near pools and spas have extra rules about distance and protection. We do not install garden lights in a pool zone without checking the layout. See spa electrical requirements.

Cost guide for 2026

These are guides only. We quote after seeing the site.

  • Single wall light replaced like for like on an existing circuit: typically one to two hundred dollars installed, plus the fitting.
  • New wall lights on an existing circuit, three or four fittings with a sensor: often several hundred dollars.
  • New outdoor circuit from the switchboard with a few fittings: commonly from several hundred to a couple of thousand dollars, depending on distance.
  • Landscape lighting scheme with transformer, buried cable and ten or more fittings: a quoted project, usually in the low thousands.
  • LED floodlight with sensor at the side of the house: usually a few hundred dollars.

Choosing fittings for Melbourne conditions

Melbourne gets heat, cold, wind-driven rain and, in some suburbs, salt. Powder-coated aluminium is fine inland. Within a few kilometres of the bay, specify stainless 316 or marine-grade finishes. Warm-white LED (around 2700–3000 K) looks natural on brick and timber; cold white feels like a car park. Dimmable drivers and shielded fittings reduce glare into neighbours’ bedrooms. A fitting that points up into trees may also attract insects; downlights from eaves reduce that.

Maintenance and lifespan

Good LED outdoor fittings last ten years or more. The first failures are usually seals and cable glands, not the LEDs themselves. We use gel-filled or silicone-sealed joints in garden runs and leave service loops so a damaged section can be cut and rejoined. A yearly look after winter catches loose fittings and water ingress early.

Planning a scheme that does not cost twice

The cheapest time to run cable is before the paving, deck or landscaping goes in. Tell your landscaper where you want fittings and we will lay conduit with draw cords so future lamps can be added without digging. A single spare conduit across a path costs very little at the time and saves a concrete cut later.

Zone the lights. A common mistake is putting every outdoor light on one switch. Separate the security and path lighting (on a sensor or dusk-to-dawn timer) from the entertaining lights on the deck (on a dimmer). That cuts running costs and stops the whole yard glaring at midnight. Add a switched powerpoint near the front door for Christmas lights, and you will not run a lead through a window every December.

Finally, check the fittings are serviceable. A tiny sealed LED that cannot be replaced is cheap until it fails in year three. Choose fittings with replaceable modules where you can.

FAQ

Can I use solar spikes instead?
For a decorative border, yes. For a path you rely on, or a security light, the output and reliability are not in the same league as wired lights.
Do lights need their own safety switch?
They need RCD protection. Usually a shared RCD on the circuit is fine, and nuisance trips can be reduced by splitting outdoor and indoor circuits.
Will you match existing copper lights?
Often yes, or we can retrofit LED lamps into the old housing if the fitting is sound.
Can you put lights on a smart switch?
Yes. Timer and sunset schedules are popular and reduce the electricity you use.
Bayside extra cost?
Marine-grade fittings and sealed joints add cost, but cheaper hardware can fail within a year in Brighton or Williamstown.
How long does installation take?
Wall lights: a couple of hours. A garden circuit: usually a day, plus trench time if the soil is hard.

See electrical, lighting design and installation, outdoor powerpoint installation, electrician in Brighton and electrician in Williamstown.

Want the yard lit properly?

We design the circuit, protect it and quote the full job. Call 1300 24 11 47.

Need a Melbourne electrical technician?

We're one call away — 24/7 emergency service, live answer, upfront pricing.