Old VIR wiring being replaced in a Melbourne heritage home
Electrical

Old house rewiring Melbourne - when you need it and what it costs

Kevin · Licensed Electrician 9 min read

Old house rewiring Melbourne: the short version

Infographic summarising the key points of Old house rewiring Melbourne - when you need it and what it costs.

Melbourne has a large proportion of pre-1970 housing stock - Victorian terraces, Edwardian bungalows, post-war brick veneer - much of it with original or early-replacement wiring. Here's how to tell if your home's wiring is past its safe service life and what a full or partial rewire costs in 2026.

When does wiring need replacing?

Wiring doesn't have a fixed mandatory replacement date, but condition and type determine when it must go. The two main types of concern in Melbourne homes:

VIR wiring (pre-1960s)

Vulcanised India Rubber insulation was used until roughly the late 1950s. The rubber degrades with age, heat, and UV exposure, becoming brittle and cracked. Cracked VIR insulation is an immediate fire and electrocution risk. If your home has VIR wiring that has not been replaced, it should be considered life-expired and requires full replacement. Signs include:

  • Cloth or fabric-wrapped cables (sometimes with a cotton braid outer).
  • Brown or black rubber insulation visible at terminations or junction boxes.
  • A pre-war or early post-war home that hasn't had documented electrical work.

Early PVC wiring (1960s–1975)

Early PVC compounds had lower temperature ratings and some contained plasticiser formulations that leach out over decades, leaving the PVC stiff and brittle. Early PVC is not as immediately dangerous as VIR, but an insulation resistance test will show whether the insulation is still performing within safe limits.

Warning signs your wiring needs attention

  • Persistent burning smell with no obvious source.
  • Intermittent power loss to circuits (loose terminations in degraded wire).
  • Safety switch tripping with no obvious appliance cause (earth leakage through degraded insulation).
  • Discolouration around outlets or switches (heat from poor contact).
  • Breakers or fuses blowing repeatedly on lightly loaded circuits.
  • Low insulation resistance readings on a test (below 1 MΩ is concerning, below 0.5 MΩ is a fail).

Energy Safe Victoria recommends having older homes inspected by a licensed electrician every 5–10 years. For pre-1960 homes, a professional assessment is overdue if it hasn't been done in the last decade.

Full rewire vs partial rewire

Full rewire

Replaces all wiring from the switchboard outward - every circuit, every outlet, every fitting. Required when:

  • VIR wiring is present throughout (it cannot be safely patched - it all goes).
  • Insulation resistance tests show widespread failure across multiple circuits.
  • Major renovation is being done (walls open anyway - the incremental cost of a rewire during reno is much lower than doing it later).

Partial rewire

Replaces specific circuits or sections identified as defective. This works when:

  • One or two circuits have failed insulation resistance while others test fine.
  • Extensions or additions have substandard wiring while the main house is sound.
  • Specific known DIY or unlicensed work needs to be replaced.

Partial rewires are cheaper upfront but can become false economy if the underlying wiring continues to degrade. Get clear advice on the remaining life of untouched circuits before accepting a partial approach.

House rewiring cost Melbourne 2026

Home typeFull rewire cost rangeNotes
2 bedroom unit / cottage$8,000 – $14,000Includes new switchboard
3 bedroom single storey$12,000 – $20,000Includes new switchboard and RCDs
4 bedroom single storey$16,000 – $26,000More circuits, longer runs
Double storey (any size)Add $3,000 – $6,000Upper floor access, inter-floor cable runs
Heritage/brick constructionAdd $2,000 – $5,000Harder access, surface conduit in some areas

These ranges assume standard cavity-wall construction. Solid brick heritage homes require surface-mounted conduit in walls where cable cannot be threaded - this increases both material and labour costs. Asbestos-containing materials (common in pre-1990 homes) require special handling and may require a licenced asbestos assessor before work proceeds.

What's included in a rewire quote

A full rewire quote should include: new switchboard with RCDs and MCBs on all circuits, all new cabling from board to each outlet and fitting, new outlet and switch faceplates, smoke alarm installation or replacement, certificate of electrical safety, and notification to Energy Safe Victoria as required. Make sure the quote explicitly includes the switchboard - some quotes exclude it and it adds $1,500–$3,500.

Rewiring during renovation - timing matters

The most cost-effective time to rewire is when walls are already open for renovation. If you're doing a kitchen renovation, bathroom renovation, or extension, have the electrician run all new wiring before the plasterer comes in. Adding circuits after walls are closed again adds significant cost and time. Plan the electrical scope before the build scope, not after.

How 24/7 Service Mate approaches rewiring projects

We start with an insulation resistance test and switchboard audit to confirm the scope. For full rewires we provide a fixed-price quote itemised by circuit and zone. We coordinate with your builder or plasterer where renovation work is concurrent. All rewires are lodged with Energy Safe Victoria and full documentation provided on completion.

Heritage and period homes: rewiring without damaging original features

Melbourne has a high concentration of Victorian-era, Edwardian, and interwar homes where original cornices, architraves, timber skirtings, and lath-and-plaster walls are as important as the wiring itself. A careful rewiring approach routes new cable through the roof cavity and wall plates where possible, minimising plaster cuts. Where cuts are unavoidable, we use discrete access points and can make good with matching plaster or recommend trusted plasterers to complete the restoration. For heritage-listed properties in councils like Boroondara, Stonnington, and Yarra, we recommend confirming with your building surveyor before any works that penetrate original fabric. The extra planning pays off: the finished result looks intentional rather than like an afterthought, and the wiring is fully compliant with AS/NZS 3000 regardless of the building’s age.

FAQ

Do I need to move out during a rewire?
For a full rewire, power is off to sections of the home as work progresses - typically 1–2 circuits at a time. Most homeowners stay in the home during a rewire, though it helps to have one area with power restored each night. Total duration for a 3–4 bedroom home is typically 3–5 days.
Will rewiring damage my walls?
In standard cavity-wall construction, new cables are fished through wall cavities with minimal cutting. Some access holes are required at switch and outlet locations. Any patches are made good before completion. Heritage solid-brick homes need surface conduit in some runs - your electrician will advise where.
Can I use homeowner insurance to cover rewiring costs?
Standard home insurance does not cover rewiring on the basis of age or deterioration - that's a maintenance obligation. Insurance may contribute if a fault caused by degraded wiring leads to fire damage, but prevention is not a covered item. Some home warranty products cover pre-existing electrical defects in newly purchased homes - check your contract.
What's the difference between rewiring and a switchboard upgrade?
A switchboard upgrade replaces the protective devices (breakers, RCDs) and the board itself, but does not touch the wiring behind the walls. A rewire replaces the wiring. Both are often needed together in pre-1980 homes - a new switchboard on old VIR wiring provides limited safety benefit.

For local help, see our Melbourne electrical services, electrician in Richmond, electrician in Melbourne CBD. Our emergency electrician in Richmond page covers scope, pricing and 24/7 dispatch. Emergency? See our emergency electrician in Richmond. Related guides: EV charger at home: 3 questions to ask before booking installation in Melbourne, Home security system installation Melbourne: cameras, sensors, outdoor power, and what a licensed electrician actually does.

Need a Melbourne electrical technician?

We're one call away — 24/7 emergency service, live answer, upfront pricing.