Split system install quote path
Heating & Cooling

Split System Air Conditioner Installation Cost Melbourne 2026

24/7 Service Mate · Heating and cooling advice team 8 min read

Split system install quote path

Flow from room heat-load calc through unit selection, install and commissioning.
Price depends on kW capacity, pipe run length, wall penetration difficulty, electrical circuit add and outdoor mount type — not just the box price. We measure the room, specify the right kW, quote pipe and electrical together, then commission with vacuum and leak test before handover. Related: Split system installation

What drives split install cost up or down

Comparison of a simple back-to-back install and a long pipe-run multi-storey install.
Back-to-back installs on a single-storey wall sit at the lower end. Multi-storey pipe runs, ducted concealment, crane lifts, asbestos eaves and new switchboard circuits add labour and materials. Cheapest quote often omits electrical — always confirm dedicated circuit is included.

What the finished job looks like

Drag the slider. These are illustrations of typical jobs, so you know what to expect.

Illustrated serviced split system
Illustrated split system that is not cooling
Before After
Split system back on Fault found, unit serviced, cooling restored. Typical job — illustration

A split system air conditioner is the most popular HVAC option for Melbourne apartments, townhouses, and individual rooms. Installation costs vary significantly by size, brand, complexity, and the condition of the wall and electrical supply. This 2026 guide gives you real Melbourne market costs so you can evaluate quotes.

Split system installation cost Melbourne 2026

System sizeSuitable forSupply + install cost
2.0–2.5 kWSmall bedroom or study (up to ~20 m²)$1,200–$1,800
3.5 kWStandard bedroom or small living room (20–30 m²)$1,600–$2,400
5.0–6.0 kWMedium living room or open plan (30–50 m²)$2,000–$3,200
7.0–8.0 kWLarge open plan or master suite (50–70 m²)$2,800–$4,200
9.0–12.0 kWVery large spaces or commercial$3,800–$6,000+

These costs include supply, installation labour, refrigerant line set (up to 5m run), electrical connection to an existing outlet or sub-board, and commissioning. Additional charges apply for longer line sets, brick or concrete walls, upper-floor outdoor units, and switchboard upgrades.

What affects installation cost?

Line set length

Standard quotes assume 3–5m of refrigerant line between the indoor and outdoor unit. Additional metres typically cost $80–$150/m. Melbourne terrace houses and multi-storey apartments often have long line set runs that add $300–$800 to the installation cost.

Wall penetration type

Brick, double-brick, or rendered walls require core drilling and take significantly longer than timber-framed walls. Expect $100–$200 additional for brick penetrations.

Electrical supply

Split systems from 3.5 kW up require a dedicated 15A or 20A circuit. If no suitable circuit is present at the indoor unit location, an electrician must run a new circuit from the switchboard. This adds $300–$700 depending on distance and switchboard condition.

Switchboard capacity

Older Melbourne homes may not have switchboard capacity for a new circuit. If the switchboard needs upgrading, this cost is separate — see our switchboard upgrade cost guide.

Top split system brands for Melbourne homes

BrandPositioningNotes for Melbourne
DaikinPremium — JapaneseIndustry-leading efficiency; excellent low-temp heating performance
Mitsubishi ElectricPremium — JapaneseVery quiet; Hyper Heating range performs well in Melbourne winters
FujitsuMid-premiumStrong local service network; good Melbourne winter performance
PanasonicMid-rangeGood value; Nanoe-X air purification is a premium feature
Samsung / LGMid-rangeGood value; Wi-Fi standard on most models
Kelvinator / HisenseBudgetLower upfront cost; higher servicing frequency noted

What size split system do I need for Melbourne?

Sizing rules of thumb for Melbourne's climate (temperate, 0–43°C range):

  • ~100–125W per m² for standard residential rooms with ceiling insulation
  • Add 20–30% for rooms with north-facing windows or poor insulation
  • Slightly oversize (10–15%) for the outdoor temperature extremes Melbourne experiences

A professional load calculation by your installer is always more accurate than rules of thumb — ask your technician to perform a room assessment before recommending a capacity.

Do I need an electrician or an HVAC technician?

In Victoria, split system installation requires both:

  • A licensed refrigeration mechanic (REF licence) for the refrigerant circuit, indoor and outdoor unit installation, and commissioning
  • A licensed electrician for the dedicated circuit, isolation switch, and switchboard connection

Most HVAC companies have both licences in-house. Always confirm both licences are held before engaging an installer.

Split system installation in Melbourne: suburb-by-suburb considerations

Council and strata requirements for split system installation

Most Melbourne councils treat a residential split system air conditioner as exempt development — no planning permit is required as long as the outdoor unit is not visible from the street and noise levels comply with EPA standards. However, if your property is in a heritage overlay or a strata/owners corporation, different rules apply. In a strata property, you must obtain approval from the owners corporation before installing an outdoor condenser unit on common property (typically the external wall or roof). Your strata manager or the owners corporation rules will confirm the approval process. In heritage overlay properties, an outdoor unit that would be visible from the street or laneway may require a planning permit from your local council. 24/7 Service Mate’s Andy advises on siting options during the quote to avoid permit issues.

Electrical requirements and switchboard capacity

Split system air conditioners require a dedicated power circuit connected to the switchboard. Most modern Melbourne homes with a 63-amp supply have capacity for a standard residential split system (2.5–8.5 kW) without a switchboard upgrade. Older homes with fuse-wire switchboards or small 32–40 amp supply may require an electrical upgrade before installation — a licensed electrician must assess the switchboard and wiring. 24/7 Service Mate coordinates both the HVAC installation (Andy) and electrical connection (Kevin) so you only make one booking call.

Split system running costs in Melbourne

A 2.5 kW split system running on electricity at Melbourne’s average residential tariff of approximately 30–35 cents per kWh costs roughly $0.25–$0.35 per hour to heat or cool a small room (with a COP of 3–4). A 7 kW system for a large living area costs $0.55–$0.85 per hour. Inverter technology (standard on all modern systems) reduces running costs by 30–40% vs older fixed-speed units by matching output to demand rather than cycling on and off. If you are replacing an old fixed-speed unit, the running cost reduction often offsets a significant portion of the installation cost over 3–5 years.

Split system sizing guide for Melbourne homes

Choosing the right capacity split system is as important as the installation itself. An undersized unit runs constantly without reaching set temperature; an oversized unit short-cycles, wearing out the compressor prematurely and delivering poor dehumidification. As a guide for Melbourne’s climate:

  • Bedroom (12–15 m²): 2.5 kW
  • Open-plan living area (30–50 m²): 5–7 kW
  • Large open plan (50–80 m²) or north-facing with high sun exposure: 7–10 kW

These are rule-of-thumb guides. A proper Manual J-style load calculation accounts for ceiling height, insulation, window orientation, and shade. 24/7 Service Mate’s Andy does a proper room assessment at quote stage — call 1300 24 11 47 to book your free site visit and installation quote.

Popular split system brands installed by 24/7 Service Mate in Melbourne include Daikin, Mitsubishi Electric, Fujitsu, Panasonic, and LG. All carry at least a 5-year parts warranty. Our installation warranty covers labour and refrigerant connections for 12 months, and we are a registered warranty service provider for major brands so you have one number for any post-installation issue. Same-week installation is available for most Melbourne suburbs. Call 1300 24 11 47 to get a fixed-price installation quote today.

Manufacturer warranty registration is completed by 24/7 Service Mate at the time of installation.

FAQ

How long does split system installation take?
A standard installation (existing circuit, simple wall penetration, short line set) takes 2–4 hours. Complex installations can take a full day.
Can a split system be installed in a Melbourne apartment?
Yes, but you typically need body corporate approval for the outdoor unit placement. Most Melbourne apartment buildings have designated outdoor unit locations for split systems on balconies or building penetrations. Confirm with your body corporate before ordering.

Get a split system installation quote in Melbourne

Fixed-price quotes, all brands, licensed refrigeration mechanics and electricians. Call 1300 24 11 47.

For local help, see our Melbourne HVAC services, HVAC technician in Richmond, HVAC technician in St Kilda. Our split system service and repair page covers scope, pricing and 24/7 dispatch. Emergency? See our emergency HVAC repair in Richmond. Related guides: Ducted air conditioning installation cost Melbourne - full breakdown by home size, Split system vs ducted: which is right for your Melbourne home in 2026.

Need a Melbourne heating & cooling technician?

We're one call away — 24/7 emergency service, live answer, upfront pricing.