If garden taps blast, flexi hoses fail every couple of years, and pipes bang when a washer shuts, mains pressure may be too high for the house. A pressure limiting valve is a plumbing device, not a tap aerator.
The short version
- A cheap gauge on a washing-machine tap tells you a lot. Over about 500 kPa inside the house is hard on hoses and valves.
- Flexi hose bursts under vanities are a classic high-pressure plus old hose combination. Related: flexi hose failure.
- A PLV on the incoming line protects the whole house. Fitting one shower restrictor does not.
- Guide: an accessible incoming PLV is a quoted install; chasing the main under a slab is a different job.
- We measure first. Not every bang is pressure; some are water hammer arrestors or loose pipes.
Why Melbourne pressure runs high
Mains pressure in Melbourne depends on where the house sits relative to storage tanks and pump stations. Low-lying suburbs near the bay and the Yarra flats often get high static pressure because the water has a long fall to reach them. Houses at the bottom of a hill can see well over 700 kPa at night, when demand is low, and that stress is invisible until something fails.
Plumbing standards expect pressure inside the building to be limited, with 500 kPa the usual ceiling for fixtures. Many older homes were built before that was routinely enforced, and some never had a limiting valve fitted. The result is a house whose taps and hoses work fine for years, then fail one after another.
Signs the house is over-pressured
- Taps spit or hiss when first opened.
- Washing-machine and dishwasher inlet hoses burst or weep at the nuts.
- Toilet cistern valves leak, run on or whistle.
- Your hot water system relief valve drips regularly. See hot water PRV leaking.
- Pipes bang when a tap or appliance shuts off quickly.
- Garden hose attachments pop off with no warning.
High pressure vs water hammer
High pressure is a constant force. Hammer is a shock when a valve slams. You can have both. Hammer gets arrestors and clipping; high pressure gets a PLV. Related: water hammer and low water pressure (the opposite problem).
How we test
We fit a gauge to an outside tap or the meter-side test point with the house quiet, then again with a tap running. The static figure shows the worst case; the dynamic one shows what you actually experience. If static is over 500 kPa and the house has no limiting valve, we recommend one. If there is already a valve and the figure is still high, it may have failed or been set wrong, which happens often with old units.
Where it goes
Usually after the meter, before the house branches, with a provision to test. Some heaters want a set arrangement with an expansion path. We follow the heater maker, not a habit. A strainer ahead of the valve keeps grit from jamming the seat, and a union either side makes future replacement a short job. In a concrete driveway or slab-on-ground house, the valve may need to sit in a small pit at the front boundary so the lid can be reached later.
DIY stop point
You can fit a cheap pressure gauge from a hardware store to an outdoor tap and read the number. That is useful and safe. Stop there. Cutting into the incoming line is regulated plumbing work, needs a Certificate of Compliance, and a wrongly fitted valve can deadhead a heater or make the relief valve weep. A garden-tap regulator protects one hose and nothing inside the house.
Cost guide for 2026
These are guides only; the final price depends on pipe type and access.
- Pressure test and written reading: often bundled into a call-out.
- Replacing an existing PLV in an accessible location: commonly a few hundred dollars.
- New PLV with strainer and unions on an accessible incoming line: a quoted standard install, often several hundred dollars.
- Accessible meter pit or side path: standard; concrete driveway over the main: detection and excavation extra. You approve the invasive bit separately.
- Replacing perished flexi hoses at the same visit: small extra per hose, and a good time to do it.
What goes wrong when pressure stays high
Pressure damage is cumulative. A copper pipe is fine at 800 kPa on day one; the tap washers, solenoid valves in the dishwasher, cistern float valves and the thermoplastic nuts on flexible hoses are what suffer. They fail one at a time, often over several years, and each failure is blamed on bad luck. A tap gets replaced, then a cistern, then a hose bursts at 3 am and soaks the cabinet and the floor under it. The common thread is rarely spotted.
High pressure also shortens the life of a hot water system. The relief valve on a storage heater lifts more often, the tank sees more cyclic stress and the expansion path gets used more. If your PTR valve drips on a regular basis, the incoming pressure is the first thing we measure. Related: hot water overflow pipe leaking.
A limiting valve also tames shower and tap performance in a good way. Many people expect a pressure drop and then comment that the water feels more controllable and the shower rose is less noisy.
FAQ
- Will a PLV make the shower weak?
- Set correctly, it should feel normal, not firehose and not dribble.
- Do heat pumps need different pressure?
- They need the right incoming pressure and expansion. We check the model.
- Can I fit a cheap garden-tap regulator instead?
- That protects one tap. The house flexis stay exposed.
- How long does a PLV last?
- Often 8–15 years. Grit and no strainer shorten it.
- Which suburbs have high mains?
- Varies by zone and hill. We measure on site rather than assume from the postcode. Low-lying streets near the Yarra and the bay are where we most often see high readings, but a gauge is the only way to know.
- Does an insurer care?
- Burst-hose claims are common. A documented pressure reading and a fitted PLV is a better story than “it just burst”.
Related reading
See plumbing, leak detection, burst pipe first five minutes, plumber in Camberwell and plumber in Ringwood.
Hoses bursting and taps blasting?
We measure pressure and quote a proper incoming valve. Call 1300 24 11 47.