6 Common Continuous Flow Hot Water Problems in Melbourne and How to Fix
Plumbing

6 Common Continuous Flow Hot Water Problems in Melbourne and How to Fix Them

Steve · Licensed Plumber 8 min read

6 Common Continuous Flow Hot Water Problems in Melbourne and How to Fix Them: the short version

Infographic summarising the key points of 6 Common Continuous Flow Hot Water Problems in Melbourne and How to Fix Them.

A continuous flow (instantaneous) hot water system is one of Melbourne’s most popular hot water choices — no running-out-of-hot-water, wall-mounted, space-saving, and efficient on gas. But when it develops a fault, you are left with no hot water at all, unlike storage systems that stay warm for hours after a failure. This guide from Steve, our licensed Melbourne plumber, walks through the 6 most common continuous flow hot water problems, what causes each, and whether the fix is a DIY check or a licensed plumber call.

Gas smell or suspected gas leak? If you smell gas near your continuous flow unit, shut off the gas supply at the meter and call your gas network provider and a licensed gas plumber immediately. Do not attempt to reset or restart the unit.

Problem 1: Unit ignites but water never gets hot (or barely warm)

Common causes

This is the most frustrating fault — the unit fires up, you can hear it working, but the water never reaches a comfortable temperature. The most likely causes are:

  • Temperature set too low: Continuous flow units have a temperature controller (a dial, digital display, or remote control). Melbourne homes with Rinnai Infinity or Rheem units often have a remote controller near the main bathroom. Check that the set point is at least 50–60°C. If the controller battery has died, the unit may default to a low temperature.
  • Hot and cold crossed at the unit: If the unit was recently serviced or a nearby tap or shower was recently replaced, it is possible the hot and cold water lines at the unit have been reversed. This is a plumber call to correct.
  • Heat exchanger scale buildup: In Melbourne’s harder-water areas, calcium deposits can reduce heat exchanger efficiency over time. Annual descaling at service prevents this. A severely scaled heat exchanger produces warm water but cannot reach set temperature.
  • Insufficient gas flow: If the gas service line to the unit is undersized or if multiple gas appliances are running simultaneously in the home, the unit may not receive enough gas to achieve full temperature output. This is more common in older Melbourne homes where the original gas line was sized for fewer appliances than are now installed.

What to check yourself

Check the temperature set point on the controller first. Replace the remote controller battery if it has not been replaced in the last 2 years. If these checks do not resolve the issue, call a licensed gas plumber.

Problem 2: Unit will not ignite at all — no hot water

Check the simple causes first

A continuous flow unit that produces only cold water and shows no sign of ignition is a common fault with several possible causes. Before calling a plumber, check:

  • Gas supply: Has the gas been turned off elsewhere? Check your gas meter and ensure the isolation tap on the gas supply line to the unit is open. If other gas appliances in the home (stove, central heating) are also not working, the gas supply to the property may be interrupted — contact your gas network provider.
  • Water flow rate: Continuous flow units require a minimum flow rate (typically 2–4 litres per minute) to trigger ignition. A partially closed tap or low water pressure below the activation threshold will prevent ignition. Try fully opening the hot water tap.
  • Power supply: Many modern continuous flow units require mains power (for the electronic ignition and controls) even though they run on gas. Check that the unit’s power supply is connected and the circuit breaker has not tripped.
  • Pilot light (older models): Some older continuous flow units have a standing pilot light. If the pilot has been extinguished by wind (common for external wall-mounted units in Melbourne’s autumn and winter), it needs to be relighted. Follow the manufacturer’s pilot relighting instructions on the unit.

When to call a plumber

If gas is confirmed flowing, water pressure is normal, power is connected, and the unit still will not ignite, the fault is internal — a failed ignition module, a faulty flow sensor, or a gas solenoid valve issue. These require a licensed gas plumber for diagnosis and repair.

Problem 3: Temperature fluctuates or spikes during shower

Why this happens in Melbourne homes

Temperature fluctuations during a shower are a known limitation of continuous flow systems that is exacerbated by simultaneous water use. When a second person turns on a kitchen tap or flushes a toilet while you are showering, the total cold water flow rate and pressure changes, which affects the ratio of cold water mixing with the hot water output from the continuous flow unit and can cause a brief temperature spike or drop. Modern units with modulating burners handle this better than older units, but all instantaneous systems are more susceptible to fluctuation than storage systems.

A specific cause: single-lever tap or tempering valve fault

If the temperature spikes occur consistently at the same point in the shower rather than randomly, the issue may be in the shower mixer itself rather than the hot water unit — a worn ceramic cartridge in the mixer can cause temperature instability. The unit should also have a tempering valve (a thermostatic mixing valve) installed to limit maximum outlet temperature to 50°C at sanitary fixtures; a failing tempering valve can allow higher temperatures to pass through. Tempering valve compliance in Victoria is regulated under AS/NZS 3500 — a licensed plumber should check this valve at your annual hot water service.

Problem 4: Cold-water sandwich between uses

Is this a fault or a feature?

The “cold-water sandwich” — a burst of cold water when you turn on the hot tap a few minutes after previously using it — is a normal characteristic of all continuous flow systems, not a fault. When you turn off a continuous flow tap, the hot water remaining in the pipe between the unit and the outlet cools to ambient temperature. When you turn on the tap again shortly after, that cold column of water must first pass the outlet before the newly-heated water arrives.

The effect is most noticeable in the kitchen, where short intervals between tap uses are common. It is typically less noticeable in the bathroom, where showers are extended uses.

Reducing the cold-water sandwich effect

The main variable within your control is the pipe run length between the unit and the outlet — the shorter the run, the faster hot water arrives. If your continuous flow unit is installed on an external wall far from the main bathroom, the cold water sandwich will be longer than if the unit is closer. A licensed plumber can assess whether a recirculation system is practical for your specific installation, but this is a significant addition to cost and is rarely installed in residential settings.

Problem 5: Hot water pressure drops when the heater fires

Flow restriction or undersized supply line

If hot water pressure at the tap drops noticeably when the continuous flow unit ignites — creating a brief low-pressure sensation — the most common cause is a partially blocked water filter (most Rinnai and Rheem units have an inline filter screen at the cold water inlet) or an undersized cold water supply line to the unit. Melbourne’s older homes sometimes have 15 mm copper pipe feeding the hot water unit where a 20 mm line would provide better flow. A plumber can inspect and clean the filter and assess the supply line size.

Problem 6: Error code on the continuous flow unit display

Common error codes across Melbourne brands

BrandCommon errorMeaningDIY check
Rinnai InfinityCode 11No ignition — no gas / ignition faultCheck gas supply; if gas is on, call plumber
Rinnai InfinityCode 12Flame failure after ignitionCheck gas pressure; call plumber
Rinnai InfinityCode 65Fan motor faultDo not run unit; call plumber
Rheem 27E1Ignition failureCheck gas and power; reset once; call if persists
Rheem 27E5Overheating / blocked flueCheck flue outlet clearance; call plumber
Bosch HydropowerE01 / blink patternIgnition faultCheck gas; reset; call plumber if repeats

Most error codes should not be repeatedly reset — if a code clears and returns within the same day, the underlying cause has not resolved. A licensed gas plumber can read fault history from modern units and diagnose the root cause. For hot water replacement cost guidance, see our hot water replacement cost Melbourne 2026 guide.

Common continuous flow brands installed across Melbourne

  • Rinnai Infinity: The market-leading brand in Melbourne’s inner suburbs. The 16, 20, 24, 26, and 32 series cover single-person apartments through large family homes. Rinnai service parts are widely stocked by Melbourne plumbing suppliers.
  • Rheem: Installed across Melbourne particularly in new builds and renovations from the 1990s onward. Rheem continuous flow units are well-supported by licensed plumbers across all suburbs.
  • Bosch: Less common but well-regarded. The Hydropower range is popular in Melbourne’s apartment market. Bosch service parts are available but less universally stocked than Rinnai.
  • Dux: Common in Melbourne’s outer ring and in properties upgraded in the 2000s–2010s. Dux units are serviced by most licensed Melbourne gas plumbers.

When to service your continuous flow hot water unit in Melbourne

Annual servicing is the manufacturer-recommended schedule

Most Rinnai, Rheem, and Bosch continuous flow units recommend annual servicing. Melbourne’s hard water in outer eastern suburbs (Box Hill, Doncaster, Ringwood, Bayswater) accelerates scale buildup in the heat exchanger, making annual descaling more important in these areas than in the softer-water inner-city supply zones.

Annual service typically includes: inlet filter clean, gas pressure check, ignition test, heat exchanger inspection and descale where needed, flue check, tempering valve check, and overall operation confirmation. Expect to pay $180–$350 for an annual continuous flow service in Melbourne 2026.

Frequently asked questions

Why does my continuous flow hot water go cold after a few minutes?
If hot water starts warm and turns cold after a few minutes, the most likely cause is the unit’s overheat protection shutting the burner off (typically due to a blocked flue, inadequate clearance around the unit, or a heat exchanger issue). It can also be a flow sensor fault that causes the unit to lose ignition. Both require a licensed plumber to diagnose.
How long does a continuous flow hot water system last in Melbourne?
A well-maintained continuous flow unit lasts 15–20 years. Units in Melbourne’s outer eastern suburbs where water hardness is higher need more frequent heat exchanger descaling to reach the upper end of that range. Annual servicing is the single most important factor in longevity. See our comparison in the hot water system types Australia guide.
Can I repair a continuous flow unit myself in Victoria?
No. Any work on the gas-side of the system — including gas connections, the burner, solenoid valve, heat exchanger, and ignition components — must be carried out by a licensed gas plumber. This is non-negotiable under the Gas Safety Act 1997 (Vic). Work on the gas side of appliances by unlicensed persons is both illegal and dangerous.
My Rinnai Infinity shows code 11 — what should I do?
Code 11 on Rinnai Infinity units indicates no ignition detected. Check the gas supply is on (meter valve open, no gas outage in your area). Try one manual reset. If the code returns after reset, call a licensed Melbourne gas plumber — the fault may be a gas valve, ignition electrode, or PCB issue that requires professional diagnosis.

Continuous flow hot water fault in Melbourne?

Call 1300 24 11 47 — licensed Melbourne gas plumbers available 24/7, dispatched across Melbourne to all inner and middle suburbs.

For local help, see our Melbourne plumbing services, plumber in Richmond, plumber in Brunswick. Our hot water system repair and replacement page covers scope, pricing and 24/7 dispatch. Emergency? See our emergency plumber in Richmond. Related guides: Heat Pump Hot Water Melbourne 2026: Cost, Victorian Rebate, Running Costs, and What Installation Involves, Hot Water No Pressure Melbourne: 6 Causes and What Your Plumber Fixes.

Need a Melbourne plumbing technician?

We're one call away — 24/7 emergency service, live answer, upfront pricing.