Hot Water Smells Like Rotten Eggs? Causes and Fixes in Melbourne Homes
Plumbing

Hot Water Smells Like Rotten Eggs? Causes and Fixes in Melbourne Homes

Steve · Licensed Plumber 7 min read

Hot Water Smells Like Rotten Eggs? Causes and Fixes in Melbourne Homes

Infographic diagram for Hot Water Smells Like Rotten Eggs? Causes and Fixes in Melbourne Homes.

A sulphur or rotten-egg smell from the hot water in your Melbourne home is almost always caused by hydrogen sulphide gas produced by bacterial activity inside the hot water storage tank, or by a reaction between the sacrificial anode rod and naturally occurring sulphates in Melbourne’s water supply. While the smell is unpleasant and alarming, it is usually not an immediate safety emergency — but it does indicate a hot water system fault that should be addressed. This guide from Steve, our licensed Melbourne plumber, explains the four causes and the correct fix for each.

Why hot water — and not cold — smells of sulphur

The anode rod and bacterial reaction

Electric storage hot water systems (and many gas storage systems) in Melbourne homes include a sacrificial magnesium or aluminium anode rod inside the tank. The anode rod is designed to corrode preferentially, protecting the tank lining from rust. However, in water with naturally high sulphate concentrations, the magnesium anode can react with sulphate-reducing bacteria in the tank to produce hydrogen sulphide — the gas that smells like rotten eggs. Melbourne’s water supply has moderate sulphate levels, and the combination of an ageing anode rod with anaerobic bacteria in a warm storage tank is the most common cause of hot water odour complaints.

Why cold water is not usually affected

Cold water passes through the pipes too quickly for bacterial growth and does not interact with an anode rod. If both hot and cold water smell sulphurous, the source is more likely in the water supply main rather than the hot water system — in that case, contact your water retailer (South East Water, Yarra Valley Water, or Melbourne Water) to report the issue.

The four causes of smelly hot water

1. Worn or exhausted anode rod

The most common cause. An anode rod that has been fully consumed (down to the wire core) can allow bacteria to thrive in the tank. In Melbourne’s slightly corrosive water, electric storage tanks have a recommended anode inspection interval of every 5 years. In practice, many Melbourne homeowners do not realise an anode rod exists in their system until a plumber identifies it as a fault. The fix is anode rod replacement, typically $150–$300 parts and labour by a licensed plumber.

2. Anaerobic bacteria colonisation in the tank

If a hot water system has been unused for a period (holiday home, rental property between tenancies, or a system that was underutilised due to thermostat issues), anaerobic bacteria can colonise the tank. The solution is a thermal disinfection procedure: raising the system thermostat to 60°C or above and running each hot water outlet for several minutes to flush the tank and kill bacteria. The Victorian Building Authority (VBA) recommends that all hot water storage systems operate at a storage temperature of at least 60°C to prevent Legionella and bacterial growth.

3. Incorrect thermostat setting (temperature too low)

Systems set to store water below 60°C create conditions where sulphate-reducing bacteria thrive. Energy-saving advice to reduce hot water thermostat settings to 45°C or 50°C is appropriate only for systems with a tempering valve installed on the outlet (which blends to a safe delivery temperature). Systems without a tempering valve must store at 60°C or above, as mandated by Australian Standard AS/NZS 3500. An incorrect thermostat setting is an easy and free fix: locate the thermostat on the tank and increase to 60°C. Allow 2–4 hours for the system to reach temperature, then run hot water at each outlet for 1–2 minutes.

4. Aluminium anode rod in high-sulphate water

Some hot water systems manufactured for the Australian market use aluminium anode rods rather than magnesium. In water with higher sulphate concentrations, aluminium anodes can produce more hydrogen sulphide than magnesium anodes. If your system has an aluminium anode and your area is experiencing odour issues, switching to a zinc-alloy or magnesium anode rod may reduce the problem. A plumber servicing the system can identify the anode rod material and advise.

How to fix smelly hot water: decision guide

DiagnosisDIY fix?Plumber fix
System stored below 60°C (low thermostat)Yes — increase thermostat to 60°C and flushOnly if thermostat is inaccessible or faulty
System unused for extended periodPartial — raise temp and flush each outletPlumber for full thermal disinfection procedure
Worn anode rodNo — requires depressurising systemAnode replacement: $150–$300
Anode type unsuitable for Melbourne waterNoAnode swap (magnesium or zinc-alloy): $150–$250
Both hot and cold smellNo — network issue, report to water retailerCall water retailer first

Hot water temperature and safety in Melbourne

AS/NZS 3500.4 requires storage temperature of at least 60°C and delivery temperature no higher than 50°C at bathroom outlets (45°C in aged care and childcare settings). This means:

  • Store at 60°C (kills bacteria including Legionella)
  • Deliver via a thermostatic mixing valve (TMV) or tempering valve that blends hot with cold to a safe delivery temperature

A system stored at 45°C without a TMV is both a plumbing standard violation and a bacterial growth risk. If your system does not have a tempering valve, raising the thermostat to 60°C fixes the bacterial issue and is correct practice. If you are unsure whether your system has a tempering valve, a licensed plumber can check during a service visit.

How often should Melbourne hot water systems be serviced?

For electric storage systems, Melbourne plumbers generally recommend:

  • Anode rod inspection at 5 years
  • Temperature and pressure relief (TPR) valve test annually
  • Full tank flush and anode replacement at 8–10 years
  • Consider system replacement at 10–12 years (electric storage) or 15–20 years (continuous flow)

For hot water replacement cost context, see our hot water replacement cost Melbourne guide. For continuous flow troubleshooting, see our continuous flow hot water problems guide.

Frequently asked questions

Is it safe to shower in water that smells like rotten eggs?
In most cases, hot water with a mild hydrogen sulphide odour is not dangerous for bathing. It is aesthetically unpleasant but not a health risk at typical residential concentrations. However, if the smell is very strong or you have vulnerable household members (very young children, elderly, or immunocompromised), it is prudent to address the cause promptly. If both hot and cold water smell, call your water retailer — this may indicate a mains supply issue that requires investigation.
How long does it take for the smell to go away after raising the thermostat?
After raising the thermostat to 60°C and allowing the system to reach temperature (usually 2–4 hours for a 125–315 L electric storage system), running each hot water outlet for 2–3 minutes flushes the hydrogen sulphide from the pipes. Most homeowners notice a significant improvement within 24 hours. If the smell persists after a full temperature cycle and flush, the anode rod is likely the ongoing cause and needs replacement.
Can I replace the anode rod myself?
Technically yes, but it requires shutting off the system, draining a portion of the tank, and applying significant torque to an anode rod that may have been in place for years and can be difficult to remove. Most Melbourne homeowners arrange this as part of a plumber service visit rather than a DIY project. The cost is modest and the plumber can also test the TPR valve and inspect the system condition at the same time.

Hot water smelling in your Melbourne home?

Call 1300 24 11 47 — licensed Melbourne plumbers service hot water systems, replace anode rods, and flush systems. dispatched across Melbourne to all Melbourne suburbs.

For local help, see our Melbourne plumbing services, plumber in Richmond, plumber in Brunswick. Our hot water system repair and replacement page covers scope, pricing and 24/7 dispatch. Emergency? See our emergency plumber in Richmond. Related guides: Heat Pump Hot Water Melbourne 2026: Cost, Victorian Rebate, Running Costs, and What Installation Involves, Hot Water No Pressure Melbourne: 6 Causes and What Your Plumber Fixes.

Need a Melbourne plumbing technician?

We're one call away — 24/7 emergency service, live answer, upfront pricing.